P.S. High value 100-105 faq are available on Google Drive, GET MORE: https://drive.google.com/open?id=10aMCxNhtGaQ1g5X4WURwuSZDkYQMo5JZ
New Cisco 100-105 Exam Dumps Collection (Question 8 - Question 17)
Q1. Refer to the exhibit.
A network associate has configured OSPF with the command: City(config-router)# network 192.168.12.64 0.0.0.63 area 0
After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? (Choose three.)
A. FastEthernet0 /0
B. FastEthernet0 /1
C. Serial0/0
D. Serial0/1.102
E. Serial0/1.103
F. Serial0/1.104
Answer: B,C,D
Explanation:
The u201cnetwork 192.168.12.64 0.0.0.63 equals to network 192.168.12.64/26. This network has:
+ Increment: 64 (/26= 1111 1111.1111 1111.1111 1111.1100 0000)
+ Network address: 192.168.12.64
+ Broadcast address: 192.168.12.127
Therefore all interface in the range of this network will join OSPF.
Q2. What OSPF command, when configured, will include all interfaces into area 0?
A. network 0.0.0.0 255.255.255.255 area 0
B. network 0.0.0.0 0.0.0.0 area 0
C. network 255.255.255.255 0.0.0.0 area 0
D. network all-interfaces area 0
Answer: A
Explanation:
Example 3-1 displays OSPF with a process ID of 1 and places all interfaces configured with an IP address in area 0. The network command network 0.0.0.0 255.255.255.255 area 0
dictates that you do not care (255.255.255.255) what the IP address is, but if an IP address is enabled on any interface, place it in area 0.
Example 3-1 Configuring OSPF in a Single Area
router ospf 1
network 0.0.0.0 255.255.255.255 area 0
Reference: http://www.ciscopress.com/articles/article.asp?p=26919&seqNum=3
Q3. What is the default administrative distance of the OSPF routing protocol?
A. 90
B. 100
C. 110
D. 120
E. 130
F. 170
Answer: C
Explanation:
Default Distance Value Table
This table lists the administrative distance default values of the protocols that Cisco supports:
If the administrative distance is 255, the router does not believe the source of that route and does not install the route in the routing table.
Q4. Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.)
A. Global addresses start with 2000::/3.
B. Link-local addresses start with FE00:/12.
C. Link-local addresses start with FF00::/10.
D. There is only one loopback address and it is ::1.
E. If a global address is assigned to an interface, then that is the only allowable address for the interface.
Answer: A,D
Q5. Refer to the exhibit.
The ports that are shown are the only active ports on the switch. The MAC address table is shown in its entirety. The Ethernet frame that is shown arrives at the switch.
What two operations will the switch perform when it receives this frame? (Choose two.)
A. The MAC address of 0000.00aa.aaaa will be added to the MAC address table.
B. The MAC address of 0000.00dd.dddd will be added to the MAC address table.
C. The frame will be forwarded out of port fa0/3 only.
D. The frame will be forwarded out of fa0/1, fa0/2, and fa0/3.
E. The frame will be forwarded out of all the active ports.
Answer: A,D
Explanation:
If the switch already has the MAC address in its table for the destination, it will forward the frame directly to the destination port. If it was not already in its MAC table, then they frame would have been flooded out all ports except for the port that it came from. It will also add the MAC address of the source device to its MAC address table
Q6. Refer to the exhibit.
Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this router?
A. 10.1.1.2
B. 10.154.154.1
C. 172.16.5.1
D. 192.168.5.3
Answer: C
Explanation:
The highest IP address of all loopback interfaces will be chosen -> Loopback 0 will be chosen as the router ID.
Q7. Which two statements describe the process identifier that is used in the command to configure OSPF on a router? (Choose two.)
Router(config)# router ospf 1
A. All OSPF routers in an area must have the same process ID.
B. Only one process number can be used on the same router.
C. Different process identifiers can be used to run multiple OSPF processes
D. The process number can be any number from 1 to 65,535.
E. Hello packets are sent to each neighbor to determine the processor identifier.
Answer: C,D
Explanation:
Multiple OSPF processes can be configured on a router using multiple process IDu2021s. The valid process IDu2021s are shown below:
Edge-B(config)#router ospf
<1-65535> Process ID
Q8. Which two commands will display the current IP address and basic Layer 1 and 2 status of an interface? (Choose two.)
A. router#show version
B. router#show ip interface
C. router#show protocols
D. router#show controllers
E. router#show running-config
Answer: B,C
Explanation:
The outputs of u201cshow protocolsu201d and u201cshow ip interfaceu201d are shown below:
Global values:Internet Protocol routing is enabledSerial0/0 is up, line protocol is downInternet address is 10.1.1.1/30Serial0/1 is up, line protocol is downInternet address is 209.65.200.225/30Serial0/2 is up, line protocol is downSerial0/3 is up, line protocol is downNVI0 is up, line protocol is upInterface is unnumbered. Using address of NVI0 (0.0.0.0)Loopback0 is up, line protocol is upInternet address is 10.1.10.1/32Loopback1 is up, line protocol is upInternet address is 10.1.2.1/27Loopback6 is up, line protocol is up
Serial0/0 is up, line protocol is downInternet address is 10.1.1.1/30Broadcast address is 255.255.255.255Address determined by non-volatile memoryMTU is 1500 bytesHelper address is not setDirected broadcast forwarding is disabledMulticast reserved groups joined: 224.0.0.5Outgoing access list is not setInbound access list is not setProxy ARP is enabledLocal Proxy ARP is disabledSecurity level is defaultSplit horizon is disabledICMP redirects are always sentICMP unreachables are always sentICMP mask replies are never sentIP fast switching is enabledIP fast switching on the same interface is enabledIP Flow switching is disabledIP CEF switching is disabledIP Feature Fast switching turbo vectorIP multicast fast switching is enabledIP multicast distributed fast switching is disabledIP route- cache flags are FastRouter Discovery is disabledIP output packet accounting is disabledIP access violation accounting is disabledTCP/IP header compression is disabledRTP/IP header compression is disabledPolicy routing is disabledNetwork address translation is enabled, interface in domain insideBGP Policy Mapping is disabledWCCP Redirect outbound is disabledWCCP Redirect inbound is disabledWCCP Redirect exclude is disabled
Q9. Refer to the exhibit.
The two routers have had their startup configurations cleared and have been restarted. At a minimum, what must the administrator do to enable CDP to exchange information between R1 and R2?
A. Configure the router with the cdp enable command.
B. Enter no shutdown commands on the R1 and R2 fa0/1 interfaces.
C. Configure IP addressing and no shutdown commands on both the R1 and R2 fa0/1 interfaces.
D. Configure IP addressing and no shutdown commands on either of the R1 or R2 fa0/1 interfaces.
Answer: B
Explanation:
If the no shut down commands are not entered, then CDP can exchange information between the two routers. By default, all Cisco device interfaces and ports are shut down and need to be manually enabled.
Q10. Refer to the exhibit.
A network technician is asked to design a small network with redundancy. The exhibit represents this design, with all hosts configured in the same VLAN. What conclusions can be made about this design?
A. This design will function as intended.
B. Spanning-tree will need to be used.
C. The router will not accept the addressing scheme.
D. The connection between switches should be a trunk.
E. The router interfaces must be encapsulated with the 802.1Q protocol.
Answer: C
Explanation:
The proposed addressing scheme is on the same network. Cisco routers will not allow you to assign two different interfaces to be on the same IP subnet.
100% Regenerate Cisco 100-105 Questions & Answers shared by Certleader, Get HERE: https://www.certleader.com/100-105-dumps.html (New 347 Q&As)