1Z0-597 Exam - SPARC T4-Based Server Installation Essentials

NEW QUESTION 1
In the following example, Power OnSelfTest(POST) reports an uncorrectablememory error affectingthe following locations:
/SYS/PM0/CMP0/B0B0/CH1/D0
/SYS/PM0/CMP0/B0B1/CH1/D0
The error wasdetected by POST running on which node, core, and standard?

• A. Node 0, core 7, strand 2
• B. Node 2, core 7, strand 0
• C. Node 7, core 2, strand 0
• D. Node 0, core 2, strand 7

Answer: A

NEW QUESTION 2
The amount of disk space recommended by the Enterprise Installation Standards (EIS) for
the root slice is for UFS File and Solaris 10.

• A. 5 GB
• B. 10 GB
• C. 13 GB
• D. 18 GB

Answer: A

NEW QUESTION 3
During an installation, you have selected two disks to be used for your ZFS root pool. What is the impact?

• A. Only single disk configurations are supported for the root pool, so Solaris will use the current boot disk for the root pool.
• B. Only single disk configurations are supported during the initial creation of a root poo
• C. Mirrored pools can only be created after the initial installation.
• D. A single ZFS volume will be used for the swap area and dump device.
• E. A mirrored two disk configuration is set up for the root pool.

Answer: D

Explanation:

Reference:http://docs.oracle.com/cd/E19082-01/817-2271/ggset/index.html(bulleted point
#3, second para)

NEW QUESTION 4
In planning for the installation of a SPARC T4 server, you notice that a more recent version of a patch is available than what is currently on the EIS-DVD. According to the Enterprise Installation Standards (EIS) methodology, what should you do?

• A. Always install the most recent version of a patch
• B. Delay Installation until the updated patch is published to the EIS-DVD
• C. Do not Install the patch, unless instructed to do so by an EIS-Alert
• D. Never Install patches outside of the EIS-DVD

Answer: A

NEW QUESTION 5
Based on the Enterprise Installation Standards (EIS), why should Oracle Explorer Data Collector be run with the “-i” switch after initial system power-on and setup are complete?

• A. To remove confidential customer IP addresses from the Explorer output
• B. To provide a baseline of the initial system configuration
• C. To collect local Intelligent Platform management Interface (IPMI) data
• D. To collect remote Oracle ILOM snapshot data

Answer: C

NEW QUESTION 6
A faulty DIMM needs to be replaced on a SPARC T4-2 server. What are two ways to determine which DIMM on a memory riser is faulty?

• A. Run the Oracle ILOM show faulty command.
• B. Run Oracle VTS software.
• C. Run the Oracle ILOM –al command.
• D. Press the Remind button on the memory riser.

Answer: AD

NEW QUESTION 7
You are installing a SPARC T4 server at a customer site using a single-phase power feed. The power outlet is 15 meters (16.4 feet) from device. Which Enterprise Installation Standard (EIS) document would you have highlighted this issue prior to installation?

• A. Site audit report
• B. Test procedure plan
• C. Power routing map
• D. Server operational checklist

Answer: D

NEW QUESTION 8
A power supply fails on a SPARC T4-4 server and a replacement is not available. What should you do?

• A. Remove the failed power supply immediately
• B. Leave the failed power supply installed
• C. Power down the server
• D. Unconfigure the failed power supply

Answer: B

Explanation:

Reference:http://docs.oracle.com/cd/E23411_01/html/E23412/z40002a31392437.html(See the note)

NEW QUESTION 9
Error conditions by POST, Oracle Solaris Predictive Self-Healing (PSH), and Oracle ILOM are forward to which component for fault handling?

• A. POST
• B. Oracle VTS
• C. Oracle ILOM
• D. Oracle Solaris PSH

Answer: C

Explanation:

Reference:http://docs.oracle.com/cd/E23075_01/pdf/E23078.pdf(page 24, third para)

NEW QUESTION 10
You are troubleshooting an installation and have run Oracle Explorer Data Collector. What should you do with the output?

• A. Have it analyzed by the Oracle Risk Analysis Services (ORAS) knowledge engine.
• B. Have it analyzed by the Remote Diagnostic Agent (RDA) tool.
• C. Review the output and address the identified configuration errors.
• D. Calculate the system operational risk (e.g., the chance of the system to go out of service due to a hardware issue.)

Answer: C

NEW QUESTION 11
You have printed the partition(slice) informationfor a disk. What type of labeldoes it have?

• A. SMI
• B. EFI
• C. e2label
• D. xfs_admin

Answer: C

NEW QUESTION 12
What is out-of-order execution?

• A. A feature of certain processors, where instructions are processed based on the availability of data.
• B. A feature multicore processors, where a core can be given processing priority over the other cores.
• C. A memory architecture feature, where specific data can be delivered to processors at the fastest possible rate.
• D. A feature of certain operating systems, where programs are executed based on the availability of data.

Answer: C

NEW QUESTION 13
According to Enterprise Installation Standards (EIS), which is recommended when creating virtual disk devices for use in guest domain?

• A. Create a new volume from an existing ZFS pool
• B. Use file containers
• C. Use the file containers and ZFS clones to multiply images
• D. Use a disk slice directly

Answer: C

NEW QUESTION 14
During installation, what happens if both power supplies are not cabled at the same time on a SPARC T4-2 server?

• A. Nothing
• B. OpenBoot PROM is disabled
• C. The service processor will not power on
• D. The Oracle ILOM will signal a fault

Answer: D

Explanation:

Reference:http://docs.oracle.com/cd/E23075_01/html/E23076/z40004b81409406.html(see the second note on the page)

NEW QUESTION 15
How many XAUI (10 GbE Attachment Unit Interfaces) ports are provided per SPARC T4 processor?

• A. 1
• B. 2
• C. 3
• D. 4

Answer: B

NEW QUESTION 16
On a SPARC T4 server running Oracle Solaris 10, you execute the following command:
# lucreate –c sol_run –m /:/dev/dsk/c0t4d0s0:ufs -m /usr:/dev/dsk/c0t4d0s3:ufs –n sol_tan What is the result?

• A. Create a new boot environment named “sol_tan” and name the active boot environment “sol_run”.
• B. Create a new boot environment named “sol_named” and name the active boot environment “sol_tan”.
• C. Replaces the existing boot environment “sol_run” with “sol_tan”
• D. Replaces the existing boot environment “sol_tan” with “sol_run”

Answer: A

NEW QUESTION 17
What package should be installed if you wish to harden the control domain on a SPARC T4 server running Oracle Solaris 10 and Oracle VM Server for SPARC 2.1?

• A. SUNWldm
• B. SUNWdmp2v
• C. SUNWsst
• D. SUNWjass

Answer: D

Explanation:

Reference:http://docs.oracle.com/cd/E27363_01/doc.121/e27511/ftr_ovm_sparc_mgmt.ht
m(15.6.2 - see the first note under this heading)

NEW QUESTION 18
You lost your Oracle ILOM settings after a service processor firmware update. Why?

• A. You did not enable the Preserve Configuration option.
• B. You did not back up the Oracle ILOM configuration.
• C. Oracle ILOM settings must be re-established after every firmware update.
• D. You used the Oracle ILOM web interface rather than the CLI to perform the update.

Answer: A

NEW QUESTION 19
You are trying to reach the OpenBoot prompt (ok) from Oracle Solaris on a SPARC T4-1 system running Oracle VM Server for SPARC. The OpenBoot firmware is not available. Why is the OpenBoot prompt not available?

• A. It has been removed from memory.
• B. It was not installed on the system.
• C. The service processor property “auto-boot” is disabled.
• D. An incorrect version of OpenBoot firmware is installed.

Answer: D

NEW QUESTION 20
You are running Oracle Solaris on a SPARC T4 server and wish to enable network traffic control and guest domains. What action needs to be performed?

• A. Nothing, since networking between the control and guest domains are automatically enabled
• B. Add a virtual network device to each guest domain
• C. Configure the virtual switch device as a network device
• D. Set up an I/O domain that has direct access to a physical I/O device

Answer: B

NEW QUESTION 21
You have configured DNS and have determined that the services processor serial number for your target server is 0641AMA007. What is the host name of this server?

• A. SUN-0641AMA007
• B. SUNCMM0-0641AMA007
• C. SUNCMM1-0641AMA007
• D. SUNSP-0641AMA007

Answer: A

NEW QUESTION 22
As part of our test procedure plan, you need to confirm that savecore is configured correctly. Which test should you use?

• A. Explore Data Collector Test
• B. Solaris VTS Test
• C. Solaris Crash Dump Test
• D. Savecore Test

Answer: C

NEW QUESTION 23
System errorscan go undetected by the Oracle VTS test, since many are detected, managed, and reported by Oracle Solaris Predictive Self-Healing. What is one way to display these errors and faults?

• A. Review the VTS error file
• B. Review the output of fmdump
• C. Review the system log files
• D. Review the VTS kernel error log

Answer: D

NEW QUESTION 24
According to the Enterprise Installation Standards (EIS), what is the minimum amount of time SunVTS should be run?

• A. 10 minutes
• B. 20 minutes
• C. 30 minutes
• D. 1 hour

Answer: D

NEW QUESTION 25
......