Updated Cisco 200-105 exam questions and 200-105 braindumps from Dumpslabs.com. Pass the CCNA Routing and Switching 200-105 exam with our 200-105 VCE dumps. Start 200-105 Exam Now.
2024 Cisco Official New Released 200-105 Q&As
100% Free Download! 100% Pass Guaranteed!
https://www.certleader.com/200-105-dumps.html
P.S. Verified 200-105 answers are available on Google Drive, GET MORE: https://drive.google.com/open?id=15qdYN17ESAKqiw2FrpOPw3870_4rbe12New Cisco 200-105 Exam Dumps Collection (Question 6 - Question 15)Q6. Which statement about slow inter VLAN forwarding is true?A. The VLAN is experiencing slowness in the point-to-point collisionless connection.B. The VLANs are experiencing slowness because multi
P.S. Exact 200-105 dump are available on Google Drive, GET MORE: https://drive.google.com/open?id=15qdYN17ESAKqiw2FrpOPw3870_4rbe12New Cisco 200-105 Exam Dumps Collection (Question 11 - Question 20)Question No: 11Which EIGRP for IPv6 command can you enter to view the link-local addresses of the neighbors of a device?A. show ipv6 eigrp 20 interfacesB. show ipv6 route eigrpC. show ipv6 eigrp neighbo
P.S. Actual 200-105 dumps are available on Google Drive, GET MORE: https://drive.google.com/open?id=1LPOwiv-vOUqlzBFPqF4sLauwGHst3olwNew Cisco 200-105 Exam Dumps Collection (Question 1 - Question 10)Question No: 1Refer to the exhibit.From R1, a network administrator is able to ping the serial interface of R2 but, unable to ping any of the subnets attached to RouterB. Based on the partial outputs i
Q1. - (Topic 3) The output of the show frame-relay pvc command shows "PVC STATUS = INACTIVE". What does this mean? A. The PVC is configured correctly and is operating normally, but no data packets have been detected for more than five minutes. B. The PVC is configured correctly, is operating normally, and is no longer actively seeking the address of the remote router. C. The PVC is configured
Q1. - (Topic 2) Which two are advantages of static routing when compared to dynamic routing? (Choose two.) A. Configuration complexity decreases as network size increases. B. Security increases because only the network administrator may change the routing table. C. Route summarization is computed automatically by the router. D. Routing tables adapt automatically to topology changes. E. An e
Q1. - (Topic 2) What are two benefits of using a single OSPF area network design? (Choose two.) A. It is less CPU intensive for routers in the single area. B. It reduces the types of LSAs that are generated. C. It removes the need for virtual links. D. It increases LSA response times. E. It reduces the number of required OSPF neighbor adjacencies. View AnswerAnswer: B,C Explanation: OSP
Q1. - (Topic 1) Which port state is introduced by Rapid-PVST? A. learning B. listening C. discarding D. forwarding View AnswerAnswer: C Explanation: Spanning Tree from PVST+ to Rapid-PVST Migration Configuration Example Reference 1: http://www.cisco.com/en/US/products/hw/switches/ps708/products_configuration_example 09186a00807b0670.shtml Reference 2: http://www.cisco.com/en/US/tech/tk3
Q1. - (Topic 3) Which command allows you to verify the encapsulation type (CISCO or IETF) for a Frame Relay link? A. show frame-relay lmi B. show frame-relay map C. show frame-relay pvc D. show interfaces serial View AnswerAnswer: B Explanation: map will show frame relay encapsulation (cisco or ietf) http://www.cisco.com/en/US/docs/ios/12_2/wan/command/reference/wrffr4.html#wp102934 "sho
Q1. - (Topic 3) What command is used to verify the DLCI destination address in a Frame Relay static configuration? A. show frame-relay pvc B. show frame-relay lmi C. show frame-relay map D. show frame relay end-to-end View AnswerAnswer: C Explanation: Cisco Frame Relay Configurations http://www.ciscopress.com/articles/article.asp?p=170741&seqNum=9 show frame-relay map The show frame-
Q1. - (Topic 3) Which two statements about using the CHAP authentication mechanism in a PPP link are true? (Choose two.) A. CHAP uses a two-way handshake. B. CHAP uses a three-way handshake. C. CHAP authentication periodically occurs after link establishment. D. CHAP authentication passwords are sent in plaintext. E. CHAP authentication is performed only upon link establishment. F. CHAP ha
Q1. - (Topic 3) Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers? A. IETF B. ANSI Annex D C. Q9333-A Annex A D. HDLC View AnswerAnswer: A Explanation: Cisco supports two Frame Relay encapsulation types: the Cisco encapsulation and the IETF Frame Relay encapsulation, which is in conformance with RFC 1490 and RFC 2427. The former is often used
Q1. - (Topic 2) What does a router do if it has no EIGRP feasible successor route to a destination network and the successor route to that destination network is in active status? A. It routes all traffic that is addressed to the destination network to the interface indicated in the routing table. B. It sends a copy of its neighbor table to all adjacent routers. C. It sends a multicast query
Q1. - (Topic 2) What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two.) A. It requires the use of ARP. B. It can support multiple IPv6 subnets on a single link. C. It supports up to 2 instances of OSPFv3 over a common link. D. It routes over links rather than over networks. View AnswerAnswer: B,D Explanation: Here is a list of the differences between OSPFv2 and OSPFv3:
Q1. - (Topic 2) Refer to the exhibit. A packet with a source IP address of 192.168.2.4 and a destination IP address of 10.1.1.4 arrives at the AcmeB router. What action does the router take? A. forwards the received packet out the Serial0/0 interface B. forwards a packet containing an EIGRP advertisement out the Serial0/1 interface C. forwards a packet containing an ICMP message out the Fast
Q1. - (Topic 1) Refer to the exhibit. At the end of an RSTP election process, which access layer switch port will assume the discarding role? A. Switch3, port fa0/1 B. Switch3, port fa0/12 C. Switch4, port fa0/11 D. Switch4, port fa0/2 E. Switch3, port Gi0/1 F. Switch3, port Gi0/2 View AnswerAnswer: C Explanation: In this question, we only care about the Access Layer switches (Switch3