P.S. Free 200-125 tutorials are available on Google Drive, GET MORE: https://drive.google.com/open?id=1N7mstYjhTswrvFd1eA3ZZFuxiKuT_fqh
New Cisco 200-125 Exam Dumps Collection (Question 8 - Question 17)
New Questions 8
What is the authoritative source for an address lookup?
A. a recursive DNS search
B. the operating system cache
C. the ISP local cache
D. the browser cache
Answer: A
New Questions 9
Which two Cisco IOS commands, used in troubleshooting, can enable debug output to a remote location? (Choose two)
A. no logging console
B. logging host ip-address
C. terminal monitor
D. show logging | redirect flashioutput.txt
E. snmp-server enable traps syslog
Answer: B,C
New Questions 10
Scenario:
You work for a company that provides managed network services, and of your real estate clients running a small office is experiencing network issues, Troubleshoot the network issues.
Router R1 connects the main office to internet, and routers R2 and R3 are internal routers NAT is enabled on Router R1.
The routing protocol that is enable between routers R1, R2, and R3 is RIPv2.
R1 sends default route into RIPv2 for internal routers to forward internet traffic to R1. Server1 and Server2 are placed in VLAN 100 and 200 respectively, and dare still running
router on stick configuration with router R2.
You have console access on R1, R2, R3, and L2SW1 devices. Use only show commands to troubleshoot the issues.
Server1 and Seiver2 are unable to communicate with the rest of the network. Your initial check with system administrators shows that IP address settings are correctly configured on the server side. What could be an issue?
A. The VLAN encapsulation is misconfigured on the router subinterfaces.
B. The IP address is misconfigured on the primary router interface.
C. The Router is missing subinterface configuration.
D. The Trunk is not configured on the L2SW1 switch.
Answer: A
New Questions 11
Which command sequence can you enter to create VLAN 20 and assign it to an interface on a switch?
A. Switch(config)#vlan 20 Switch(config)#Interface gig x/y Switch(config-if)#switchport access vlan 20
B. Switch(config)#Interface gig x/y Switch(config-if)#vlan 20
Switch(config-vlan)#switchport access vlan 20
C. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport trunk native vlan 20
D. Switch(config)#vlan 20
Switch(config)#Interface vlan 20 Switch(config-if)#switchport access vlan 20
E. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport trunk allowed vlan 20
Answer: A
New Questions 12
Which command can you enter to display duplicate IP addresses that the DHCP server assigns?
A. show ip dhcp conflict 10.0.2.12
B. show ip dhcp database 10.0.2.12
C. show ip dhcp server statistics
D. show ip dhcp binding 10.0.2.12
Answer: A
New Questions 13
What is the danger of the permit any entry in a NAT access list?
A. It can lead to overloaded resources on the router.
B. It can cause too many addresses to be assigned to the same interface.
C. It can disable the overload command.
D. It prevents the correct translation of IP addresses on the inside network.
Answer: A
New Questions 14
Which component of the Cisco SDN solution serves as the centralized management system?
A. Cisco OpenDaylight
B. Cisco ACI
C. Cisco APIC
D. Cisco IWAN
Answer: C
Explanation:
Cisco ACI is a comprehensiveSDN architecture. This policy-based automation solution supports a business-relevant application policy language, greater scalability through a distributed enforcement system, and greater network visibility. These benefits are achieved through the integration of physical and virtual environments under one policy model for networks, servers, storage, services, andsecurity.
New Questions 15
Which statement about DTP is true?
A. It uses the native VLAN.
B. It negotiates a trunk link after VTP has been configured.
C. It uses desirable mode by default.
D. It sends data on VLAN 1.
Answer: D
Explanation:
Disabling Dynamic Trunking Protocol (DTP)
Cisco'sDynamicTrunking Protocolcan facilitate the automatic creation of trunks between two switches. When two connected ports are configured in dynamic mode, and at least one of the ports is configured as desirable, the two switches will negotiate the formation of a trunk across the link. DTP isn't to be confused withVLAN Trunking Protocol(VTP), although the VTP domain does come into play.
DTP on the wireis pretty simple, essentially only advertising the VTP domain, the status of the interface, and it's DTP type. These packets are transmitted in the native (or access) VLAN every 60 seconds both natively and with ISL encapsulation (tagged as VLAN 1) when DTP is enabled.
New Questions 16
Which EIGRP for IPv6 command can you enter to view the link-local addresses of the neighbors of a device?
A. show ipv6 eigrp 20 interfaces
B. show ipv6 route eigrp
C. show ipv6 eigrp neighbors
D. show ip eigrp traffic
Answer: C
New Questions 17
Which function of the IP SLAs ICMP jitter operation can you use to determine whether a VoIP issue is caused by excessive end-to-end time?
A. packet loss
B. jitter
C. successive packet loss
D. round-trip time latency
Answer: D
100% Improve Cisco 200-125 Questions & Answers shared by Thedumpscentre, Get HERE: http://www.thedumpscentre.com/200-125-dumps/ (New 890 Q&As)