P.S. Exact 200-125 testing material are available on Google Drive, GET MORE: https://drive.google.com/open?id=1IiiyEYVh7VGuzQjIt9B135ONv4m9W195
New Cisco 200-125 Exam Dumps Collection (Question 4 - Question 13)
New Questions 4
Refer to the exhibit.
What is the effect of the given configuration?
A. It configures an inactive switch virtual interface.
B. It configures an active management interface.
C. It configures the native VLAN.
D. It configures the default VLAN.
Answer: A
Topic 2, Exam Set 2
74.Which function does the IP SLAs ICMP Echo operation perform to assist with troubleshooting?
A. hop-by-hop response time
B. packet-loss detection
C. congestion detection
D. one way jitter measurements
New Questions 5
Which component of a routing table entry represents the subnet mask?
A. routing protocol code
B. prefix
C. metric
D. network mask
Answer: D
Explanation:
IP Routing Table Entry Types
An entry in the IP routing table contains the following information in the order presented: Network ID.The network ID or destination corresponding to the route. The network ID can be class-based, subnet, or supernet network ID, or an IP address for a host route. Network Mask.The mask that is used to match a destination IP address to the network ID. Next Hop.The IP address of the next hop.
Interface.An indication of which network interface is used to forward the IP packet. Metric.A number used to indicate the cost of the route so the best route among possible multiple routes to the same destination can be selected. A common use of the metric is to indicate the number of hops (routers crossed) to the network ID.
Routing table entries can be used to store the following types of routes:
Directly Attached Network IDs.Routes for network IDs that are directly attached. For directly attached networks, the Next Hop field can be blank or contain the IP address of the interface on that network.
Remote Network IDs.Routes for network IDs that are not directly attached but are available across other routers. For remote networks, the Next Hop field is the IP address of a local router in between the forwarding node and the remote network.
Host Routes.A route to a specific IP address. Host routes allow routing to occur on a per-
IP address basis. For host routes, the network ID is the IP address of the specified host and the network mask is 255.255.255.255.
Default Route.The default route is designed to be used when a more specific network ID or host route is not found. The default route network ID is 0.0.0.0 with the network mask of 0.0.0.0.
New Questions 6
Which component of the routing table ranks routing protocols according to their preferences?
A. administrative distance
B. next hop
C. metric
D. routing protocol code
Answer: A
Explanation:
Administrative distance- This is the measure of trustworthiness of the source of the route.
If a router learns about a destination from more than one routing protocol, administrative distance is compared and the preference is given to the routes with lower administrative distance. In other words, it is the believability of the source of the route.
New Questions 7
Which option describes the purpose of traffic policing?
A. It prioritizes routing protocol traffic.
B. It remarks traffic that is below the CIR
C. It drops traffic that exceeds the CIR.
D. It queues and then transmits traffic that exceeds the CIR.
Answer: C
Explanation:
Traffic policing allows you to control the maximum rate of traffic transmitted or received on an interface. Traffic policing is often configured on interfaces at the edge of a network to limit traffic into or out of the network. In most Traffic Policing configurations, traffic that falls within the rate parameters is transmitted, whereas traffic that exceeds the parameters is dropped or transmitted with a different priority.
New Questions 8
If router R1 knows a static route to a destination network and then learn about the same destination network through a dynamic routing protocol, how does R1 respond?
A. It sends a withdrawal notification to the neighboring router.
B. It refuses to advertise the dynamic route to other neighbors.
C. It disables the routing protocol.
D. It prefers the static route.
Answer: D
New Questions 9
Scenario:
You are a junior network engineer for a financial company, and the main office network is experiencing network issues. Troubleshoot the network issues.
Router R1 connects the main office to the internet, and routers R2 and R3 are internal routers.
NAT is enabled on router R1.
The routing protocol that is enabled between routers R1, R2 and R3 is RIPv2.
R1 sends the default route into RIPv2 for the internal routers to forward internet traffic to R1.
You have console access on R1, R2 and R3 devices. Use only show commands to troubleshoot the issues.
Users complain that they are unable to reach internet sites. You are troubleshooting internet connectivity problem at main office. Which statement correctly identifies the problem on Router R1?
A. Interesting traffic for NAT ACL is incorrectly configured.
B. NAT configurations on the interfaces are incorrectly configured
C. NAT translation statement incorrectly configured.
D. Only static NAT translation configured for the server, missing Dynamic NAT or Dynamic NAT overloading for internal networks.
Answer: B
New Questions 10
Why is the Branch2 network 10.1 0.20.0/24 unable to communicate with the Server farm1 network 10.1 0.10.0/24 over the GRE tunnel?
A. The GRE tunnel destination is not configured on the R2 router.
B. The GRE tunnel destination is not configured on the Branch2 router.
C. The static route points to the tunnel0 interface that is misconfigured on the Branch2 router.
D. The static route points to the tunnel0 interface that is misconfigured on the R2 router.
Answer: C
Explanation:
The Branch2 network is communicating to the Server farm, which is connected to R2, via GRE Tunnel so we should check the GRE tunnel first to see if it is in u201cup/upu201d state with the u201cshow ip interface briefu201d command on the two routers.
On Branch2:
On R2:
We see interfaces Tunnel0 at two ends are u201cup/upu201d which are good so we should check for the routing part on two routers with the u201cshow running-configu201d command and pay attention to the static routing of each router. On Branch2 we see:
R2_show_run_static.jpg
The destination IP address for this static route is not correct. It should be 192.168.24.1 (Tunnel0u2021s IP address of R2), not 192.168.24.10 -> Answer C is correct.
Note: You can use the u201cshow ip routeu201d command to check the routing configuration on each router but if the destination is not reachable (for example: we configure u201cip route 10.10.10.0 255.255.255.0 192.168.24.10u201d on Branch2, but if 192.168.24.10 is unknown then Branch2 router will not display this routing entry in its routing table.
New Questions 11
Which NAT function can map multiple inside addresses to a single outside address?
A. PAT
B. SFTP
C. RARP
D. ARP
E. TFTP
Answer: A
New Questions 12
Which option describes a difference between EIGRP for IPv4 and IPv6?
A. Only EIGRP for IPv6 advertises all connected networks.
B. Only EIGRP for IPv6 requires a router ID to be configured under the routing process-
C. AS numbers are configured in EIGRP but not in EIGRPv3.
D. Only EIGRP for IPv6 is enabled in the global configuration mode.
Answer: B
Explanation:
Router ID- Both EIGRP for IPv4 and EIGRP for IPv6 use a 32-bit number for the EIGRP router ID. The 32-bit router ID is represented in dotted-decimal notation and is commonly referred to as an IPv4 address. If the EIGRP for IPv6 router has not been configured with
an IPv4 address, theeigrp router-idcommand must be used to configure a 32-bit router ID. The process for determining the router ID is the same for both EIGRP for IPv4 and IPv6.
New Questions 13
Which statement about switch access ports is true?
A. They drop packets with 802.1Q tags.
B. A VLAN must be assigned to an access port before it is created.
C. They can receive traffic from more than one VLAN with no voice support
D. By default, they carry traffic for VLAN 10.
Answer: A
Explanation:
"If an access port receives a packet with an 802.1Q tag in the header other than the access VLAN value, that port drops the packet without learning its MAC source address."
P.S. Easily pass 200-125 Exam with Dumpscollection Exact Dumps & pdf vce, Try Free: http://www.dumpscollection.net/dumps/200-125/ (573 New Questions)