Q1. The wireless network is using controller-based APs and version 7.0 MR1. The APs appear to be connected properly to the controllers. A wireless user near one of the APs reports that they are unable to connect to the network with their pre-shared key.
Which option shows the GUI path where you can check the connection status of that client?
A. WLANs > WLAN_ID > Advanced
B. Security > Clients
C. Security > Advanced > Clients
D. Monitor > Clients
E. Wireless > 802.11b/g/n > clients
Answer: D
Q2. A network engineer in the GUI of WCS version 7 wants to add an access point to a map. Where can this command be found within the drop-down menu?
A. Monitor > Maps
B. Reports > Maps
C. Monitor > Network Summary
D. Configure > Maps
Answer: A
Q3. Refer to the exhibit.
You made a manual configuration change to a controller and now you need to compare the controller configuration seen on Cisco WCS to the configuration that is present in the controller.
Which menu can you use to do compare the configurations?
A. Reports
B. Monitor
C. Configure
D. Services
E. Administration
F. Tools
Answer: C
Q4. What technology consists of small, low-power digital radios?
A. LTE
B. WiFi
C. ZigBee
D. Bluetooth
Answer: C
Q5. You are sitting in an airport preparing to use a free WLAN. When you look at the connections in your Windows 7 wireless client, you see a network name and three boxes with a yellow shield.
What does this mean?
A. You cannot connect to this WLAN.
B. An open ad hoc network is nearby.
C. The WLAN in the airport is open.
D. A secure ad hoc network is nearby.
E. A secure WLAN is in the airport.
F. You must provide a username and password to access the WLAN in the airport.
Answer: B
Q6. An engineer has been noticing the power settings on several of the office APs change from day to day ever since two more APs were installed. After logging into the WLC, the engineer verifies that the power levels on 4 of the 802.11n radios are fluctuating up and down. What is the reason for this?
A. The controller has the APs in H-REAP mode and are on a Layer 2 connection instead of Layer 3.
B. The RRM has revealed a bad survey and is attempting to power down some of the radios to make up for it.
C. The WLC has created temporary coverage holes while stepping through power levels for some of the APs.
D. Several APs have high levels of overlapping coverage in the same area and the WLC is using RRM to correct the cell sizes AP coverage.
Answer: D
Q7. An AP was reset while working on the correct association to a Cisco WCS version 7.0.
Which item was cleared during the reset?
A. static IP address
B. the location ID of the AP
C. WLC primary, secondary, tertiary
D. AP name
E. certificate
F. Nothing was cleared.
Answer: F
Q8. Microsoft Active Directory integrated machines are not authenticating to the internal WLAN. The WLAN settings are WPA2-AES-802.1x and are authenticating to a Cisco Identity Services Engine server. You investigate and note that non-domain authenticated machines are properly authenticating to the WLAN using their Active Directory credentials. Why would this problem occur?
A. The WLAN is configured improperly in group policy.
B. The ACS server is not joined to the domain, causing authentications to fail.
C. The domain machines are configured to disable the wireless adapter.
D. The non-domain machines are using local accounts that are not authenticated through the domain.
Answer: A
Q9. A customer has requested a single point of policy enforcement for LAN and WLAN. Which deployment model should be used?
A. converged
B. autonomous
C. FlexConnect
D. centralized
Answer: A
Q10. Which Cisco AnyConnect module allows you to set the parameters that are needed to connect to the wireless network?
A. NAM
B. DART
C. posture
D. telemetry
Answer: A