P.S. Verified 300-101 training materials are available on Google Drive, GET MORE: https://drive.google.com/open?id=1CwAEJEbFmyl4ZmUUqpfpE03ZrSQ7-7CS
New Cisco 300-101 Exam Dumps Collection (Question 15 - Question 22)
Q1. Which two statements about OSPF E1 routes are true? (Choose two)
A. They are preferred over interarea routes
B. They use the OSPF cost from redistribution and the OSPF cost to the ASBR.
C. They are preferred over E2 routes
D. They use only the OSPF cost to the ASBR
E. They use only the OSPF cost from redistribution
Answer: B,C
Explanation: http://blog.ine.com/2011/04/04/understanding-ospf-external-route-path- selection/
Q2. When policy-based routing (PBR) is being configured,
Which three criteria can the set command specify? (Choose three.)
A. all interfaces through which the packets can be routed
B. all interfaces in the path toward the destination
C. adjacent next hop router in the path toward the destination
D. all routers in the path toward the destination
E. all networks in the path toward the destination
F. type of service and precedence in the IP packets
Answer: A,C,F
Explanation:
Configuring Policy-Based Routing (PBR):
You can configure PBR by following these steps. Some of the steps may be omitted depending on your application for PBR. For this example, note the set condition options listed is step 3 (answers are bolded).
Step1
Define and configure the route map needed for the policy. This is accomplished with the route-map command, as discussed previously.
Step2
Define and configure the match statements the route map will use. The most common
match statements used are the following: match ip address [access-list number]
The match ip address is used to call a standard, extended, or expanded-range ACL. match length [min_packet_length_0-2147483647] [max_packet_length_0-2147483647]
The match length is used to match the Layer 3 packet length, in bytes, with all associated headers and trailers included. You must enter the minimum and maximum packet length. Use the match length command to policy route traffic based on packet size. You can deploy this to route traffic with large or small packet sizes to specific areas of the network. Step3
Configure and define the new routing policy with set commands. Multiple set commands may be used; if multiple commands are used, they are executed in the following order:
set ip {precedence [value_0-7 | name] | tos [value_0-8 | name]} set ip next-hop ip_address
set interface interface_name
set ip default next-hop ip_address set default interface interface_name
Set ip precedence {[1-7]|[routine|critical|flash|flash- override|immediate|internet|network|priority]}
Q3. A network engineer executes the show crypto ipsec sa command. Which three pieces of information are displayed in the output? (Choose three.)
A. inbound crypto map
B. remaining key lifetime
C. path MTU
D. tagged packets
E. untagged packets
F. invalid identity packets
Answer: A,B,C
Q4. Which address is used by the Unicast Reverse Path Forwarding protocol to validate a packet against the routing table?
A. source address
B. destination address
C. router interface
D. default gateway
Answer: A
Q5. Exhibit:
=================
AS65000 (R1)u2014(R2)u2013 (R3)
| |
| |
(R4) (R5)
| |
10.1.0.0/16 10.2.0.0/16
AS 65001 AS65002 Second | should be between R3 and R5
==================
Refer to exhibit. If the IGP in AS65000 is RIPv2, which networks are displayed when you enter show ip route on router R2?
A. VLSM subnts in 10.0.0.0/16 and the major network 10.2.0.0/16 only
B. VLSM subnets in 10.0.0.0/16 and the major network 10.2.0.0/16 only
C. VLSM subnets in 10.0.0.0/16 only
D. major networks 10.1.0.0/16 and 10.2.0.0/16 only
E. VLSM subnets in 10.0.0.0/16 and the major networks 10.1.0.0/16 10.2.0.0/16
Answer: D
Q6. What is the default maximum segment size for TCP traffic?
A. 536
B. 1492
C. 1500
D. 1508
E. 3340
F. 4096
Answer: A
Q7. Which interface type does a PPPoE client use to establish a session?
A. Physical
B. loopback
C. visual-template
D. dialer
Answer: D
Explanation: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/bbdsl/configuration/xe-3s/bba-pppoe-client.html
Q8. Which two methods of deployment can you use when implementing NAT64? (Choose two.)
A. stateless
B. stateful
C. manual
D. automatic
E. static
F. functional
G. dynamic
Answer: A,B
100% Rebirth Cisco 300-101 Questions & Answers shared by Certifytools, Get HERE: https://www.certifytools.com/300-101-exam.html (New 436 Q&As)