P.S. Printable 300-101 pack are available on Google Drive, GET MORE: https://drive.google.com/open?id=1oF6hAYEiseB3LPIXYA2sgTXv0r2MX46d
New Cisco 300-101 Exam Dumps Collection (Question 3 - Question 12)
Q1. Refer to the exhibit.
Which two statements are true about the router configuration? (Choose two.)
A. This configuration allows applications on the same segment to communicate via IPv4 or IPv6.
B. This configuration is referred to as a dual-stack 6to4 tunnel.
C. This configuration is referred to as a dual stack.
D. This configuration will attempt to route packets using IPv4 first, and if that fails, then IPv6.
Answer: A,C
Explanation:
This router demonstrates an example of an IPv6 Dual Stack configuration. Dual stack (Figure 1 below) runs both IPv4 and IPv6 protocol stacks on a router in parallel, making it similar to the multiprotocol network environments of the past, which often ran Internetwork Packet Exchange (IPX), AppleTalk, IP, and other protocols concurrently. The technique of deploying IPv6 using dual-stack backbones allows IPv4 and IPv6 applications to coexist in a dual IP layer routing backbone. The IPv4 communication uses the IPv4 protocol stack, and the IPv6 communication uses the IPv6 stack.
As a transition strategy, dual stack is ideal for campus networks with a mixture of IPv4 and IPv6 applications.
Figure 1: Dual-Stack Example
Q2. Which IP SLA operation can be used to measure round-trip delay for the full path and hop- by-hop round-trip delay on the network?
A. HTTP
B. ICMP path echo
C. TCP connect
D. ICMP echo
Answer: B
Q3. Which statement describes what this command accomplishes when inside and outside interfaces are correctly identified for NAT?
ip nat inside source static tcp 192.168.1.50 80 209.165.201.1 8080 extendable
A. It allows host 192.168.1.50 to access external websites using TCP port 8080.
B. It allows external clients coming from public IP 209.165.201.1 to connect to a web server at 192.168.1.50.
C. It allows external clients to connect to a web server hosted on 192.168.1.50.
D. It represents an incorrect NAT configuration because it uses standard TCP ports.
Answer: C
Q4. What is the administrative distance for EBGP?
A. 200
B. 30
C. 70
D. 20
Answer: D
Q5. Your Company trainee asks you, in the context of IPv6 and OSPF, what best describes a type 9 LSA? What should you tell her?
A. Link LSA
B. Interarea prefix LSA for ABRs
C. Router LSA
D. Switch LSA
E. Intra-area prefix LSA
F. None of the above
Answer: E
Q6. What command is needed to get the ip address assigned from the PPPOE server?
A. Interface dialer
B. pppoe enable
C. ip address negotiated
D. ip address auto negotiated
Answer: C
Q7. An engineer is using a network sniffer to troubleshoot DHCPv6 between a router and hosts on the LAN with the following configuration:
Interface Ethernet0
Ipv6 dhcp server DHCPSERVERPOOL rapid-commit
!
Which two DHCPv6 messages will appear in the sniffer logs?
A. reply
B. request
C. advertise
D. acknowledge
E. solicit
F. accept
Answer: A,E
Q8. Which functionality is required within an IP router that is situated at the boundary of an IPv4 network and an IPv6 network to allow communication between IPv6-only and IPv4-only nodes?
A. Autoconfiguration
B. Automatic 6to4 Tunnel
C. Automatic 6to4 Relay
D. Network Address Translator-Protocol Translator (NAT-PT)
E. Intrasite Automatic Tunnel Address Protocol (ISATAP)
Answer: D
Q9. An engineer executes the ip flow ingress command in interface configuration mode. What is the result of this action?
A. It enables the collection of IP flow samples arriving to the interface.
B. It enables the collection of IP flow samples leaving the interface.
C. It enables IP flow while disabling IP CEF on the interface.
D. It enables IP flow collection on the physical interface and its subinterfaces.
Answer: A
Q10. CORRECT TEXTA network engineer enables OSPF on a Frame Relay WAN connecton to various remote stes, but no OSPF adiacencies come up Which two actions are possible solutions for thisissue? (Choose Two)
A Change the network type to point-to-murpont under WAN interface
B. Enable virtual Inks
C. Change the networktype to nonbroadcast mutpoint access
D. Configure the neighbor command under OSPF process for each remote ste
E. Ensure that the OSPF process number matches among all remote stes
Answer: A, D
100% Most recent Cisco 300-101 Questions & Answers shared by 2passeasy, Get HERE: https://www.2passeasy.com/dumps/300-101/ (New 436 Q&As)