300-115 Exam - Implementing Cisco IP Switched Networks

certleader.com

Q1. A network engineer tries to configure storm control on an EtherChannel bundle. What is the result of the configuration?

A. The storm control settings will appear on the EtherChannel, but not on the associated physical ports.

B. The configuration will be rejected because storm control is not supported for EtherChannel.

C. The storm control configuration will be accepted, but will only be present on the physical interfaces.

D. The settings will be applied to the EtherChannel bundle and all associated physical interfaces.

Answer: D

Q2. Which switch feature prevents traffic on a LAN from being overwhelmed by continuous multicast or broadcast traffic?

A. storm control

B. port security

C. VTP pruning

D. VLAN trunking

Answer: A

Q3. After reviewing UDLD status on switch ports, an engineer notices that the." Which statement describes what this indicates about the status of the port?

A. The port is fully operational and no known issues are detected.

B. The bidirectional status of "unknown" indicates that the port will go into the disabled state because it stopped receiving UDLD packets from its neighbor.

C. UDLD moved into aggressive mode after inconsistent acknowledgements were detected.

D. The UDLD port is placed in the "unknown" state for 5 seconds until the next UDLD packet is received on the interface.

Answer: A

Q4. After the implementation of several different types of switches from different vendors, a network engineer notices that directly connected devices that use Cisco Discovery Protocol are not visible. Which vendor-neutral protocol could be used to resolve this issue?

A. Local Area Mobility

B. Link Layer Discovery Protocol

C. NetFlow

D. Directed Response Protocol

Answer: B

Q5. Which command correctly configures standby tracking for group 1 using the default decrement priority value?

A. standby 1 track 100

B. standby 1 track 100 decrement 1

C. standby 1 track 100 decrement 5

D. standby 1 track 100 decrement 20

Answer: A

Q6. after UDLD is implemented, a Network Administrator noticed that one port stops receiving UDLD packets. This port continues to reestablish until after eight failed retries. The port then transitions into the errdisable state. Which option describes what causes the port to go into the errdisable state?

A. Normal UDLD operations that prevent traffic loops.

B. UDLD port is configured in aggressive mode.

C. UDLD is enabled globally.

D. UDLD timers are inconsistent.

Answer: B

Q7. A server with a statically assigned IP address is attached to a switch that is provisioned for DHCP snooping. For more protection against malicious attacks, the network team is considering enabling dynamic ARP inspection alongside DHCP snooping. Which solution ensures that the server maintains network reachability in the future?

A. Disable DHCP snooping information option.

B. Configure a static DHCP snooping binding entry on the switch.

C. Trust the interface that is connected to the server with the ip dhcp snooping trust command.

D. Verify the source MAC address of all untrusted interfaces with ip dhcp snooping verify mac-address command.

Answer: B

Q8. after configuring new data VLANs 1020 through 1030 on the VTP server, a network engineer notices that none of the VTP clients are receiving the updates. What is the problem?

A. The VTP server must be reloaded.

B. The VTP version number must be set to version 3.

C. After each update to the VTP server, it takes up to 4 hours propagate.

D. VTP must be stopped and restarted on the server.

E. Another switch in the domain has a higher revision number than the server.

Answer: B

Q9. A network engineer has just deployed a non-Cisco device in the network and wants to get information about it from a connected device. Cisco Discovery Protocol is not supported, so the open standard protocol must be configured. Which protocol does the network engineer configure on both devices to accomplish this?

A. IRDP

B. LLDP

C. NDP

D. LLTD

Answer: B

Q10. When you configure private VLANs on a switch, which port type connects the switch to the gateway router?

A. promiscuous

B. community

C. isolated

D. trunked

Answer: A