300-115 Exam - SWITCH Implementing Cisco IP Switched Networks

Q1. Which two configurations can you apply to a port so that it tags traffic with VLAN 915? (Choose two.)

A. interface GigabitEthernet0/0 switchport mode access switchport access vlan 915

B. interface GigabitEthernet0/0 switchport mode trunk

switchport trunk encapsulation dot1q switchport trunk allowed vlan 915

C. interface GigabitEthernet0/0 switchport mode access switchport voice vlan 915 switchport access vlan 915

D. interface GigabitEthernet0/0.915 encapsulation dot1q 915

E. interface GigabitEthernet0/0.915 switchport mode access

switchport access vlan 915

View Answer

Q2. Which statement about the default Switch Database Management template is true?

A. The default template disables routing and supports the maximum number of unicast MAC addresses

B. The default template gives balance to all functions.

C. The default template maximizes system resources for unicast routing

D. The default template maximizes system resources for access control lists

View Answer

Q3. Which two statements about default FHRP behavior are true? (Choose two)

A. A backup GLBP active virtual gateway can become active only if the current active virtual gateway fails.

B. Preemption is enabled by default.

C. Unless specifically Configured, the priority of an HSRP router is 200.

D. A standby HSRP router becomes active if it has a higher priority than the priority of the current active router.

E. A VRRP backup virtual router becomes the master router if its priority is higher than the priority of the current master router.

View Answer

Q4. Which two options are advantages of deploying VTPv3? (Choose two)

A. It stores the VTP domain password securely as a SHA-1 hash

B. It adds on FCS field at the end of each VTP frame for consistency checking

C. It supports the propagation of private VLANs.

D. It supports the use of AES to encrypt VTP messaging

E. It can be configured to allow only one VTP server to make changes to the VTP domain

View Answer

Q5. Which two command sequences must you enter on a pair of switches so that they negotiate an EtherChannel using the Cisco proprietary port-aggregation protocol? (Choose two.)

A. channel-protocol lacp channel-group 1 mode on

B. channel-protocol pagp channel-group 1 mode auto

C. channel-protocol lacp channel-group 1 mode active

D. channel-protocol pagp channel-group 1 mode desirable

E. channel-protocol pagp channel-group 1 mode on

View Answer

Q6. Which two restrictions of the port security feature are true? (Choose two.)

A. It is not supported on destination SPAN ports.

B. It is not supported on EtherChannel port-channel interfaces.

C. Static port MAC address assignments are not supported

D. A single device can learn a maximum of three sticky MAC addresses.

E. It is not supported on PVLAN ports.

View Answer

Q7. Which two statements about HSRP timers are true? (Choose two.)

A. the default hold timer is 15 seconds

B. the default hello timer is 3 seconds.

C. the default hello timer is 5 seconds.

D. the default hold timer is 10 seconds.

E. the default hello timer is 30 seconds.

F. the default hold timer is 30 seconds.

View Answer

Q8. Which option is the maximum frame size for an 802.1Q frame?

A. 64 bytes

B. 68 bytes

C. 1518 bytes

D. 1522 bytes

View Answer

Q9. Which file lists all of the configured VLANs on a switch?

A. flash:vlan.dat

B. nvram:vlans.xml

C. flash:vlans.txt

D. nvram:vlan.txt

E. flash.config.txt

F. flash:vlan.xml

View Answer

Q10. Which three design types of capable Ethernet LANs does HSRP support? (Choose three.)

A. Multicaccess

B. Multicast

C. Broadcast

D. Unicast

E. Token Ring

F. FDDI

View Answer