300-115 Exam - SWITCH Implementing Cisco IP Switched Networks

Question No: 5

Refer to the exhibit.

Switch A, B, and C are trunked together and have been properly configured for VTP. Switch C receives VLAN information from the VTP server Switch A, but Switch B does not receive any VLAN information. What is the most probable cause of this behavior?

A. Switch B is configured in transparent mode.

B. Switch B is configured with an access port to Switch A, while Switch C is configured with a trunk port to Switch B.

C. The VTP revision number of the Switch B is higher than that of Switch A.

D. The trunk between Switch A and Switch B is misconfigured.

View Answer

Question No: 6

Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRP to provide a high availability solution.

u2022 DSW1 -primary device for VLAN 101 VLAN 102 and VLAN 105

u2022 DSW2 - primary device for VLAN 103 and VLAN 104

u2022 A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.

Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.

During routine maintenance, GigabitEthernet1/0/1 on DSW1 was shut down. All other interfaces were up. DSW2 became the active HSRP device for VLAN 101 as desired. However, after GigabitEthemet1/0/1 on DSW1 was reactivated, DSW1 did not become the active router for VLAN 101 as desired. What needs to be done to make the group for VLAN 101 function properly?

A. Enable preempt in the VLAN 101 HSRP group on DSW1.

B. Disable preempt in the VLAN 101 HSRP group on DSW2's.

C. In the VLAN 101 HSRP group on DSW1, decrease the priority value to avaluethatis less ' than the priority value configured in the VLAN 101 HSRP group on DSW2.

D. Decrease the decrement value in the track command for the VLAN 101 HSRP group on U DSWTs to a values less than the value in the track command for the VLAN 101 HSRP group on DSW2.

View Answer

Question No: 7

A network engineer has just deployed a non-Cisco device in the network and wants to get information about it from a connected device. Cisco Discovery Protocol is not supported, so the open standard protocol must be configured. Which protocol does the network engineer configure on both devices to accomplish this?

A. IRDP

B. LLDP

C. NDP

D. LLTD

View Answer

Question No: 8

The command storm-control broadcast level 75 65 is configured under the switch port connected to the corporate mail server. In which three ways does this command impact the traffic? (Choose three.)

A. SNMP traps are sent by default when broadcast traffic reaches 65% of the lower-level threshold.

B. The switchport is disabled when unicast traffic reaches 75% of the total interface bandwidth.

C. The switch resumes forwarding broadcasts when they are below 65% of bandwidth.

D. Only broadcast traffic is limited by this particular storm control configuration.

E. Multicast traffic is dropped at 65% and broadcast traffic is dropped at 75% of the total interface bandwidth.

F. The switch drops broadcasts when they reach 75% of bandwidth.

View Answer

Question No: 9

A new network that consists of several switches has been connected together via trunking interfaces. If all switches currently have the default VTP domain name "null", which statement describes what happens when a domain name is configured on one of the switches?

A. The switch with the non-default domain name restores back to "null" upon reboot.

B. Switches with higher revision numbers does not accept the new domain name.

C. VTP summary advertisements are sent out of all ports with the new domain name.

D. All other switches with the default domain name become VTP clients.

View Answer

Question No: 10

Network engineer want to use UDLD, what he need to consider?

A. udld is a non-propriety

B. udld is working with non cisco devices

C. udld is layer 1

D. udld can aggressively disabled the port after eight failed retries

View Answer

Question No: 11

Which gateway role is responsible for answering ARP requests for the virtual IP address in GLBP?

A. active virtual forwarder

B. active virtual router

C. active virtual gateway

D. designated router

View Answer

Question No: 12

When you configure a private VLAN, which type of port must you configure the gateway router port as?

A. promiscuous port

B. isolated port

C. community port

D. access port

View Answer

Question No: 13

A network engineer wants to ensure Layer 2 isolation of customer traffic using a private VLAN. Which configuration must be made before the private VLAN is configured?

A. Disable VTP and manually assign VLANs.

B. Ensure all switches are configured as VTP server mode.

C. Configure VTP Transparent Mode.

D. Enable VTP version 3.

View Answer

Question No: 14

To follow the Layer 2 switching guidelines, a network engineer decides to create a separate spanning tree for every group of 10 VLANs. Which version of spanning tree is appropriate to meet the company policy?

A. MST

B. PVST+

C. RSTP

D. RPVST+

E. STP

View Answer

Question No: 15

When a Layer 2 trunking EtherChannel is configured, which two attributes must match across the member ports? (Choose two)

A. Interface Description.

B. Spanning-tree cost.

C. spanning-tree priority

D. allowed VLANS

E. trunking mode.

View Answer