Q1. Which two protocols can be automatically negotiated between switches for trunking? (Choose two.)
A. PPP
B. DTP
C. ISL
D. HDLC
E. DLCI
F. DOT1Q
Answer: C,F
Q2. What is the default value for the errdisable recovery interval in a Cisco switch?
A. 30 seconds
B. 100 seconds
C. 300 seconds
D. 600 seconds
Answer: C
Q3. Refer to the exhibit.
What is the result of the configuration?
A. The EtherChannels would not form because the load-balancing method must match on the devices.
B. The EtherChannels would form and function properly even though the load-balancing and EtherChannel modes do not match.
C. The EtherChannels would form, but network loops would occur because the load- balancing methods do not match.
D. The EtherChannels would form and both devices would use the dst-ip load-balancing method because Switch1 is configured with EtherChannel mode active.
Answer: B
Q4. Which statement about Cisco devices learning about each other through Cisco Discovery Protocol is true?
A. Each device sends periodic advertisements to multicast address 01:00:0C:CC:CC:CC.
B. Each device broadcasts periodic advertisements to all of its neighbors.
C. Each device sends periodic advertisements to a central device that builds the network topology.
D. Each device sends periodic advertisements to all IP addresses in its ARP table.
Answer: A
Q5. what percentage of bandwidth is reduced when a stack cable is broken?
A. 0
B. 25
C. 50
D. 75
E. 100
Answer: C
Q6. Which command creates a login authentication method named "login" that will primarily use RADIUS and fail over to the local user database?
A. (config)# aaa authentication login default radius local
B. (config)# aaa authentication login login radius local
C. (config)# aaa authentication login default local radius
D. (config)# aaa authentication login radius local
Answer: B
Q7. Which feature must be enabled to eliminate the broadcasting of all unknown traffic to switches that are not participating in the specific VLAN?
A. VTP pruning
B. port-security
C. storm control
D. bpdguard
Answer: A
Q8. A network engineer is installing a switch for temporary workers to connect to. The engineer does not want this switch participating in Spanning Tree with the rest of the network; however, end user connectivity is still required. Which spanning-tree feature accomplishes this?
A. BPDUblock
B. BPDUfilter
C. BPDUignore
D. BPDUguard
E. BPDUdisable
Answer: B
Q9. What happens on a Cisco switch that runs Cisco IOS when an RSTP-configured switch receives 802.1d BPDU?
A. 802.1d does not understand RSTP BPDUs because they are different versions, but when a RSTP switch receives an 802.1d BPDU, it responds with an 802.1d BPDU and eventually the two switches run 802.1d to communicate.
B. 802.1d understands RSTP BPDUs because they are the same version, but when a RSTP switch receives a 802.1d BPDU, it responds with a 802.1d BPDU and eventually the two switches run 802.1d to communicate.
C. 802.1d does not understand RSTP BPDUs because they are different versions, but when a RSTP switch receives a 802.1d BPDU, it does not respond with a 802.1d BPDU.
D. 802.1d understands RSTP BPDUs because they are the same version, but when a RSTP switch receives a 802.1d BPDU, it does not respond with a 802.1d BPDU and eventually the two switches run 802.1d to communicate.
Answer: A
Q10. A network engineer must set the load balance method on an existing port channel. Which action must be done to apply a new load balancing method?
A. Configure the new load balancing method using port-channel load-balance.
B. Adjust the switch SDM back to "default".
C. Ensure that IP CEF is enabled globally to support all load balancing methods.
D. Upgrade the PFC to support the latest load balancing methods.
Answer: A