P.S. Pinpoint 300-135 guidance are available on Google Drive, GET MORE: https://drive.google.com/open?id=1b8IflMM01Yv-CELfeZXF0P5UV8NaZBSU
Question No: 5
The implementations group has been using the test bed to do a u2021proof-of-conceptu2021 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Answer: D
Explanation:
On R4, in the redistribution of EIGRP routing protocol, we need to change name of route- map to resolve the issue. It references route-map OSPF_to_EIGRP but the actual route map is called OSPF->EIGRP.
Question No: 6
Which of the following commands can be used to gather information about the AS- PATH of a BGP route? (Choose all that apply.)
A. show ip bgp neighbors
B. debug ip bgp updates
C. show ip route bgp
D. show ip bgp
E. show ip bgp summary
F. sh ip bgp database
Answer: B,D
Explanation: Incorrect:
show ip bgp summary: The command show ip bgp summary does not presents informations about routes.
Question No: 7
Which of the following management types can be used to deploy appropriate quality- of-service solutions to make the most efficient use of bandwidth?
A. Fault management
B. Accounting management
C. Operations management
D. Performance management
E. Security management
F. Configuration management
Answer: D
Question No: 8
Which of the following are common issues that should be considered when establishing or troubleshooting site-to-site VPNs? (Choose all that apply.)
A. User authentication
B. Overlapping IP address space
C. GRE or IPsec configuration
D. MTU size
E. VPN client software
F. Authentication server configured ly
Answer: B,C,D
Question No: 9
What level of logging is enabled on a Router where the following logs are seen?
%LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
A. alerts
B. critical
C. errors
D. notifications
Answer: D
Explanation:
Cisco routers, switches, PIX and ASA firewalls prioritize log messages into 8 levels (0-7), as shown below:
LevelLevel NameDescription
0 Emergencies System is unusable 1 Alerts Immediate action needed 2 Critical Critical conditions
3 Errors Error conditions
4 Warnings Warning conditions
5 Notifications Informational messages
6 Informational Normal but significant conditions 7 Debugging Debugging messages
When you enable logging for a specific level, all logs of that severity and greater (numerically less) will be logged. In this case we can see that logging level of 3 (as seen by the 3 in u201cLINK-3-UPDOWNu201d) and level 5 (as seen by the 5 in u201cLINEPROTO-5-UPDOWNu201d) are shown, which means that logging level 5 must have been configured. As shown by the table, logging level 5 is Notifications.
Question No: 10
The implementations group has been using the test bed to do a u2021proof-of-conceptu2021 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
What is the solution to the fault condition?
A. Disable auto summary on the EIGRP process
B. Enable EIGRP on the FastEthernet0/0 and FastEthernet0/1 interface using the no passive-interface command.
C. Change the AS number on the EIGRP routing process from 1 to 10 to much the AS number used on DSW1 and DSW2.
D. Under the EIGRP process, delete the network 10.1.4.0 0.0.0.255 command and enter the network 10.1.4.4 0.0.0.252 and 10.1.4.8 0.0.0.252 commands.
Answer: C
Explanation:
On R4, IPV4 EIGRP Routing, need to change the EIGRP AS number from 1 to 10 since DSW1 & DSW2 is configured to be in EIGRP AS number 10.
Question No: 11
Which two of the following options are categories of Network Maintenance tasks?
A. Firefighting
B. Interrupt-driven
C. Policy-based
D. Structured
E. Foundational
Answer: B,D
Explanation:
Proactive Versus Reactive Network Maintenance:
Network maintenance tasks can be categorized as one of the following: Structured tasks: Performed as a predefined plan.
Interrupt-driven tasks: Involve resolving issues as they are reported.
Reference: CCNP TSHOOT Official Certification Guide, Kevin Wallace, Chapter 1, p.7
Question No: 12
A customer network engineer has made configuration changes that have resulted in some loss of connectivity. You have been called in to evaluate a switch network and suggest resolutions to the problems.
You have configured PVST+ load balancing between SW1 and the New_Switch in such a way that both the links E2/2 and E2/3 are utilized for traffic flow, which component of the configuration is preventing PVST+ load balancing between SW1 and SW2 links
A. Port priority configuration on SW1
B. Port priority configuration on the New_Switch
C. Path cost configuration on SW1
D. Path cost configuration on the New_Switch
Answer: D
Explanation:
Here is the configuration found on the New_Switch:
This causes the port cost for link eth 1/3 to increase the path cost to 250 for all VLANs, making that link less preferred so that only eth 1/2 will be used.
Question No: 13
Scenario:
You have been asked by your customer to help resolve issues in their routed network. Their network engineer has deployed HSRP. On closer inspection HSRP doesn't appear to be operating properly and it appears there are other network problems as well. You are to provide solutions to all the network problems.
You have received notification from network monitoring system that link between R1 and R5 is down and you noticed that the active router for HSRP group 1 has not failed over to the standby router for group 1. You are required to troubleshoot and identify the issue.
A. There is an HSRP group track command misconfiguration
B. There is an HSRP group priority misconfiguration
C. There is an HSRP authentication misconfiguration
D. There is an HSRP group number mismatch
E. This is not an HSRP issue; this is routing issue.
Answer: A
Explanation:
When looking at the HSRP configuration of R1, we see that tracking has been enabled, but that it is not tracking the link to R5, only the link to R2:
R1 should be tracking the Eth 0/1 link, not 0/0 to achieve the desired affect/
Topic 5, Troubleshooting OSPF
24.Scenario:
A customer network engineer has edited their OSPF network configuration and now your customer is experiencing network issues. They have contacted you to resolve the issues and return the network to full functionality.
The 6.6.0.0 subnets are not reachable from R4. how should the problem be resolved?
A. Edit access-list 46 in R6 to permit all the 6.6.0.0 subnets
B. Apply access-list 46 in R6 to a different interface
C. Apply access-list 1 as a distribute-list out under router ospf 100 in R4
D. Remove distribute-list 64 out on R6
E. Remove distribute-list 1 in ethernet 0/1 in R4
F. Remove distribute-list 1 in ethernet 0/0 in R4
Question No: 14
FCAPS is a network maintenance model defined by ISO. It stands for which of the following?
A. Fault Management
B. Action Management
C. Configuration Management
D. Protocol Management
E. Security Management
Answer: A,C,E
Explanation:
The FCAPS maintenance model consists of the following:
FCAPS Maintenance Tasks:
u2711 Fault u2013 collect info from routers and switches, email at threshold limits, respond to trouble tickets
u2711 Configuration u2013 log changes to network h/w or s/w. alert relevant folks of planned changes
u2711 Accounting u2013 invoice users
u2711 Performance u2013 monitor network performance and deploy QoS
u2711 Security u2013 deploy firewall, VPN, IPS, create security policy, use AAA to validate credentials, etc.
Recommend!! Get the Pinpoint 300-135 dumps in VCE and PDF From Certleader, Welcome to download: https://www.certleader.com/300-135-dumps.html (New 156 Q&As Version)