Cause all that matters here is passing the Cisco 300-180 exam. Cause all that you need is a high score of 300-180 DCIT Troubleshooting Cisco Data Center Infrastructure (DCIT) exam. The only one thing you need to do is downloading Exambible 300-180 exam study guides now. We will not let you down with our money-back guarantee.
Also have 300-180 free dumps questions for you:
NEW QUESTION 1
When using a Cisco Nexus 5500 and Cisco Nexus 7000 Series Switch, how can a port channel interface be configured?
- A. Layer 3 interface
- B. Layer 3 interface in non-admin VDC only
- C. Layer 3 interface in admin VDC only
- D. Layer 3 interface in VDC 1 only
Answer: A
NEW QUESTION 2
A customer has a Cisco UCS Center cluster. The customer configures LDAP as the AAA protocol and enables SSL for LDAP. The LDAP authentication fails. Which issue is the cause of the failure?
- A. The LDAP client passed an incorrect from the trustpoint.
- B. The CA certificate is missing from the trustpoints.
- C. The LDAP server limit that is set by an administrative authority was exceeded.
- D. The LDAP time limit that is specified by either the client or the server was exceeded.
Answer: D
NEW QUESTION 3
Refer to the exhibit.
You are configuring a FCoE VDC on a Cisco Nexus 7000 Series Switch. You are required to identity compatible QoS policies for the FCoE VDC. Drag and drop the QoS policy names on the left to their correct compatibility categories on the right.
- A. Mastered
- B. Not Mastered
Answer: A
Explanation: 
NEW QUESTION 4
Refer to the exhibit.
VM-1 and VM-3 are in different EPGs but in the same BD. Which statement about the communication between VM-1 and VM-3 is true?
- A. The packet must transverse a Layer 3 interface.
- B. The flow uses unencapsulated VLANs
- C. The flow must transverse the spine.
- D. The flow stays local to the leaf switch
Answer: C
NEW QUESTION 5
When configuring LLDP on Cisco Nexus 5548 Switch, what is the purpose of LLDP hold time global configuration command?
- A. LLDP holdtime option is to set the length of time in milliseconds that a device should save LLDP information received before discarding it.
- B. LLDP holdtime option is to set the length of time in seconds that a device should save LLDP information received before discarding it.
- C. LLDP holdtime option is to set the length of time in milliseconds to wait before performing LLDP initialization on any interface.
- D. LLDP holdtime option is to set the length of time in seconds to wait before performing LLDP initialization on any interface.
Answer: B
NEW QUESTION 6
Refer to the output. feature otv
otv site-vlan 2
otv site-identifier 256
!
interface ethernet 2/0
ip address 192.0.2.1/24 ip igmp version 3
!
interface ethernet 2/1 ip address 192.0.2.2/24 ip igmp version 3
!
interface Overlay1
otv control-group 239.1.1.1 otv join-interface ethernet 2/0 otv extend-vlan 3-100
!
interface Overlay2
otv control-group 239.1.1.1 otv join-interface ethernet 2/1 otv extend-vlan 101-115
Which command best represents where the control plane configurations are applied?
- A. switch(config-if-overlay)# otv isis hello-interval 30
- B. switch(config-if)# otv isis hello-interval 30
- C. switch(config-vlan)# otv isis hello-interval 30
- D. switch(config)# otv isis hello-interval 30
Answer: A
NEW QUESTION 7
Refer to the exhibit.
When your customers have NPV problems, which two actions should you take? (Choose two.)
- A. Verify that the NPV core switch supports NPIV and that it is enabled.
- B. Ensure that the VLAN values are configured on both sides of the NPV core switch.
- C. Verify the status of the servers and external interfaces, using the show npv server status command.
- D. Ensure that the VSAN value that is configured on the device links is correct.
- E. For all the device links, ensure that the port mode on the NPV device is in Full_port mode.
Answer: AD
NEW QUESTION 8
Refer to the exhibit.
During a VSAN outage, you come across this configuration. Please select two possible causes? (Choose two)
- A. no common VSANs on both switches
- B. no common trunks
- C. no common VSAN members in the same trunk
- D. VSANs in trunk are the same, but the trunk is not up
Answer: AC
NEW QUESTION 9
Refer to the exhibit,
You configure a Cisco Nexus 5000 in NPV mode to enable multiple servers to log in over a single link to the NPV switch. Which option describes why the vfc interface is stuck on “initializing” state?
- A. The load balancing is configured incorrectly on the Cisco Nexus 5000 switch.
- B. The Version of code does not support the NPV feature.
- C. The Cisco Nexus 5000 switch does not have "feature npv" enabled.
- D. The upstream switch does not have "feature npiv" enabled.
Answer: D
NEW QUESTION 10
Refer to the exhibit.
DC-SWITCH 14 is a Cisco Nexus switch Port channel 1106 connects to a Cisco Nexus switch named DC-SWITCH10. Which cause of the I flag is likely?
- A. Port channel 1106 is administratively down.
- B. STP is blocking port channel 1106
- C. LACP is misconfigured on DC-SWITCH14
- D. LACP is misconfigured on DC-SWITCH10.
Answer: C
NEW QUESTION 11
Refer to the exhibit.
What is the cause of the ISSU failure when using the command show system internal csm global info?
- A. The command conf-t is holding a lock and not released it.
- B. The SSN feature is not enabled on both switches.
- C. The reference count is less than 1 due to a lack of successful config-sync.
- D. It cannot be determined from the output.
- E. An Administrator is logged in on another session and has a lock of the session data base to prevent ISSU.
Answer: A
NEW QUESTION 12
You plan to troubleshoot EPG communication by using atomic counters. What do you consider before using the atomic counters?
- A. Atomic counters only property in a transit, non-full-mesh topology,
- B. Atomic counters count the traffic for the endpoints that are located in different VRFs.
- C. Atomic counters do not count the traffic between EPGs that reside in different VRFs.
- D. Atomic counters also count spine proxy traffic
Answer: C
NEW QUESTION 13
Refer to the exhibit.
Which command was used to produce the output for the inband packet statistics?
- A. show hardware internal cpu-mac inband counters
- B. show system internal interface counters module
- C. show interface counters all
Answer: A
NEW QUESTION 14
Refer to the exhibit.
All the interfaces on the switch must forward traffic by using VLAN 701. Which action do you take?
- A. Enable the vPC on port channel 1101 and port channel 1102.
- B. Lower the switch priority such that it becomes the spanning tree root.
- C. Increase the switch priority such that it becomes the spanning tree root.
- D. Allow VLAN 701 on port channel 1101 and port channel 1102.
Answer: B
NEW QUESTION 15
A customer reports that it cannot establish a vPC peer link between two Cisco Nexus 5548UP Switches. The interfaces on both switches are configured and cabled correctly. The interface status is up/down on switch 1 and up/up on switch 2. Which three steps are taken to isolate the root cause? (Choose three.)
- A. ask the customer if the link was ever functional
- B. determine whether the fiber-optic cable type (single mode or multimode) matches the X2 modules
- C. swap the fiber-optic cable with one known to be good
- D. swap the transceivers between the two interfaces
- E. swap the ends of the fiber-optic cable
Answer: CDE
NEW QUESTION 16
Which two commands can you issue on a Cisco Nexus 5548UP Switch to determine which interfaces are connected to fabric extenders? (Choose two.)
- A. show fex-fabric interface
- B. show fex
- C. show fex fex-id
- D. show fex interface
- E. show fex detail
Answer: CE
NEW QUESTION 17
A customer reports that they are missing vPC peer link redundancy between two Cisco Nexus 5548UP switches. The interfaces on both switches are configured and cabled correctly. The interface status is up/down on switch 1 and up/up on switch 2, Which two steps should be taken to isolate the root cause? (Choose two.)
- A. Swap the ends of the fiber-optic cable
- B. ask the customer if the link was ever functional
- C. determine whether the fiber-optic cable manufacturer is valid under the interoperability matrix
- D. swap the transceivers between the two interfaces
- E. determine Whether the fiber-optic cable type (single mode or multimode) matches the X2 modules
Answer: AD
NEW QUESTION 18
Refer to the exhibit.
Which description of the output is true?
- A. Two VTEPs are in the VEM.
- B. Two VTEP table versions exist.
- C. Two VTEPs are in the VSM.
- D. One designated VTEP is in the bridge domain.
Answer: C
NEW QUESTION 19
A customer is troubleshooting FCoE in its network and sees pause counters increasing when it runs the command show interface eth1/5. What is the cause of this?
- A. The CNA connected to the switch is sending Xon or Xoff PFC frames.
- B. The HBA connected to the switch is sending Xon or Xoff PFC frames.
- C. Pause counters increase regularly; there is nothing to be concerned about.
- D. A firmware upgrade on the Fibre Channel adapter that is connected to the switch will fix this issue.
Answer: A
NEW QUESTION 20
Which three of these would cause two switch fabrics not to merge? (Choose three.)
- A. Two or more switches do not have at least one assigned domain ID in common.
- B. Two switches have different assigned VSANs on the connecting ports.
- C. Two switches have different assigned VLANs on the connecting ports.
- D. The static domain ID does not override the dynamic ID.
- E. The election of the static domain is only determined by the WWNs of the two switches.
- F. The physical connectivity between the two switches is not active.
Answer: ABF
NEW QUESTION 21
In Cisco NX-OS releases prior to 5.2, how should the copp-system-p-policy policy be modified to change how the supervisor module is protected from DoS attacks?
- A. Modify the policy map type control-plane copp-system-policy.
- B. Open DCNM and modify the "copp-system-p-policy" policy object.
- C. Re-run the setup utility and apply a new CoPP profile.
- D. In Cisco NX-OS versions prior to 5.2, the CoPP system profile can only be modified from the CMP CLI.
Answer: C
NEW QUESTION 22
Which action do you take to determine why the interface el/10 is not present in the core VDC for configuration?
- A. Check the admin VDC to see the port e1/10 is allocated.
- B. Check the core VDC to see if the port e1 /10 is allocated.
- C. Check to see if the cable is connected to the e1/10 interface,
- D. Check to see if vPC is enabled
Answer: A
NEW QUESTION 23
When you look at the HSRP state for devices on a VLAN that is extended by OTV, you see the following states: Active, Standby, and Listen. However, you intended each data center device to show the state as Active and Standby. What is the problem?
- A. HSRP is not configured correctly.
- B. A VACL is missing.
- C. A PACL is missing.
- D. This cannot be done.
Answer: A
NEW QUESTION 24
Which two commands will show all the OTV edge devices and their MAC addresses in all sites in the overlay? (Choose two.)
- A. show otv adjacency overlay
- B. show otv site
- C. show otv vlan
- D. show otv adjacency
- E. show mac address-table
Answer: AD
NEW QUESTION 25
Which two conditions can prevent vFC from coming up? (Choose two.)
- A. PFC is enabled.
- B. DCBX is disabled.
- C. LDP is disabled.
- D. vPC is enabled.
- E. VSAN trunking is enabled
Answer: BC
NEW QUESTION 26
Your customer is an ISP providing service to thousands of end customers. Its main concerns are focused on using up the total number of 4096 VLANs per VDC, wasting an unused block of IP addresses, and IP address management. Which technique will address these concerns?
- A. create a separate VDC to scale VLAN limitation and upgrade to Cisco Nexus 7018 Switch
- B. segment VLANs using secondary IP addresses, which will reduce the management domain
- C. create mapping between the VLAN and VSAN to run FCoE to consolidate VLAN and IP addresses
- D. use PVLANs, which will solve the scalability problem and provide IP address management
Answer: D
NEW QUESTION 27
Refer to the exhibit.
A user named user1 is unable to create roles. What must you do to resolve the issue?
- A. Assign user1 to the network-admin role.
- B. Assign user1 to the tech-admin role only.
- C. Set the user password for user1
- D. Allow user1 to log in locally
Answer: A
NEW QUESTION 28
Refer to the exhibit.
Customer is having problems with a device in VLAN100? What would fix the problem?
- A. Move the trunk port into VSAN 100.
- B. Change interface fc1fc1/1 into a trunk port and remove VSAN 100.
- C. Change interface fc2/4 into a trunk port.
- D. Change interface fc2/4 into VSAN 100.
- E. Change interface fc1fc1/2 into VSAN 100.
Answer: D
NEW QUESTION 29
......
Thanks for reading the newest 300-180 exam dumps! We recommend you to try the PREMIUM Passcertsure 300-180 dumps in VCE and PDF here: https://www.passcertsure.com/300-180-test/ (269 Q&As Dumps)