Q1. What is the CLI command to enable SNMPv3 on the Cisco Web Security Appliance?
A. snmpconfig
B. snmpenable
C. configsnmp
D. enablesnmp
Answer: A
Q2. Which two options are private-VLAN secondary VLAN types? (Choose two)
A. Isolated
B. Secured
C. Community
D. Common
E. Segregated
Answer: A,C
Explanation:
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/configuration/guid e/cli/ CLIConfigurationGuide/PrivateVLANs.html
Q3. Refer to the exhibit.
Which statement about this access list is true?
A. This access list does not work without 6to4 NAT
B. IPv6 to IPv4 traffic permitted on the Cisco ASA by default
C. This access list is valid and works without additional configuration
D. This access list is not valid and does not work at all
E. We can pass only IPv6 to IPv6 and IPv4 to IPv4 traffic
Answer: A
Q4. If you disable PortFast on switch ports that are connected to a Cisco ASA and globally turn on BPDU filtering, what is the effect on the switch ports?
A. The switch ports are prevented from going into an err-disable state if a BPDU is received.
B. The switch ports are prevented from going into an err-disable state if a BPDU is sent.
C. The switch ports are prevented from going into an err-disable state if a BPDU is received and sent.
D. The switch ports are prevented from forming a trunk.
Answer: C
Q5. Which three options correctly identify the Cisco ASA1000V Cloud Firewall? (Choose three.)
A. operates at Layer 2
B. operates at Layer 3
C. secures tenant edge traffic
D. secures intraswitch traffic
E. secures data center edge traffic
F. replaces Cisco VSG
G. complements Cisco VSG
H. requires Cisco VSG
Answer: B,C,G
Q6. What are two reasons to implement Cisco IOS MPLS Bandwidth-Assured Layer 2 Services? (Choose two.)
A. guaranteed bandwidth and peak rates as well as low cycle periods, regardless of which systems access the device
B. increased resiliency through MPLS FRR for AToM circuits and better bandwidth utilization through MPLS TE
C. enabled services over an IP/MPLS infrastructure, for enhanced MPLS Layer 2 functionality
D. provided complete proactive protection against frame and device spoofing
Answer: B,C
Q7. Which function does DNSSEC provide in a DNS infrastructure?
A. It authenticates stored information.
B. It authorizes stored information.
C. It encrypts stored information.
D. It logs stored security information.
Answer: A
Q8. If the Cisco ASA 1000V has too few licenses, what is its behavior?
A. It drops all traffic.
B. It drops all outside-to-inside packets.
C. It drops all inside-to-outside packets.
D. It passes the first outside-to-inside packet and drops all remaining packets.
Answer: D
Q9. You are the administrator of a Cisco ASA 9.0 firewall and have been tasked with ensuring that the Firewall Admins Active Directory group has full access to the ASA configuration. The Firewall Operators Active Directory group should have a more limited level of access.
Which statement describes how to set these access levels?
A. Use Cisco Directory Agent to configure the Firewall Admins group to have privilege level 15 access. Also configure the Firewall Operators group to have privilege level 6 access.
B. Use TACACS+ for Authentication and Authorization into the Cisco ASA CLI, with ACS as the AAA server. Configure ACS CLI command authorization sets for the Firewall Operators group. Configure level 15 access to be assigned to members of the Firewall Admins group.
C. Use RADIUS for Authentication and Authorization into the Cisco ASA CLI, with ACS as the AAA server. Configure ACS CLI command authorization sets for the Firewall Operators group. Configure level 15 access to be assigned to members of the Firewall Admins group.
D. Active Directory Group membership cannot be used as a determining factor for accessing the Cisco ASA CLI.
Answer: B
Q10. What can you do to enable inter-interface firewall communication for traffic that flows between two interfaces of the same security level?
A. Run the command same-security-traffic permit inter-interface globally.
B. Run the command same-security-traffic permit intra-interface globally.
C. Configure both interfaces to have the same security level.
D. Run the command same-security-traffic permit inter-interface on the interface with the highest security level.
Answer: A