Q1. CMX Facebook WiFi can allow access to the network before authentication. Which two of the following options are available? (Choose two)
A. Allow all the traffic before authentication and intercept HTTPs only.
B. Allow HTTP traffic only before authentication and block all the traffic.
C. Allow SNMP traffic only before authentication and block all the traffic.
D. Allow all the traffic before authentication and intercept HTTP only.
E. Allow HTTPs traffic only before authentication and block all other traffic.
Answer: B,D
Q2. Which two options are limitations of using an AP as a workgroup bridge? (Choose two.)
A. Only factory-configured MAPs can support WGB mode.
B. MAPs that are configured in WGB mode do not answer S36 radio measurement requests.
C. A limited subset of Layer 2 security types are supported for wireless clients of a WGB.
D. There is a limit of 20 wired client devices.
E. Multiple VLANs are not supported for wireless clients.
Answer: B,D
Q3. You have just added a new MSE to Prime Infrastructure and want to synchronize the MSE with your 5508 WLC. which is located behind a firewall in a DMZ. You notice that NMSP messages are failing between the two devices. What traffic needs to be allowed on the Firewall to ensure the MSE and WLC can communicate using NMSP?
A. UDP 16113
B. TCP 1613
C. TCP 16113
D. UDP 1613
Answer: C
Q4. A network engineer must configure a 5 GHz network to allow for the greatest density of radios possible with the least amount of co-channel interference. Which configuration best fulfills this requirement?
A. Set 802.11 h Local Power constraint to 25 dBm.
B. Set DCA to 20 MHz channels and enable Extended UNII-2 channels.
C. Enable Event Driven RRM in 5 GHz with a sensitivity of High, n
D. Configure TPC Power Threshold to -80 dBm and set interference Optimal Mode (TPCv2).
Answer: B
Q5. On which AP radio or radios is Cisco WGB association supported?
A. 2.4 GHz only
B. 2.4 or 5 GHz only
C. 2.4, 5, or 4.9 GHz
D. 5 GHz only
Answer: B
Q6. An engineer must deploy FlexConnect APs to a site that typically has 300 ms latency to the WLC. Which typical operating mode must the engineer plan on for normal operations?
A. local authentication, local switching
B. central authentication, central switching
C. central authentication, local switching
D. connected mode
Answer: A
Q7. A network engineer must ensure that corporate wireless users have a better experience than guest wireless users. Which two configurations fulfil requirement? (Choose two.)
A. Override per-SSID bandwidth contracts on the corporate WLAN to reserve bandwidth.
B. Modify the corporate WLAN to the Platinum QoS policy.
C. Enable 802.1ptag on the Gold QoS pofccyto honor prioritized traffic.
D. Adjust the guest WLAN radio policy to 80211 b/g only.
E. Change the guest WLAN to the Bronze QoS policy.
Answer: B,E
Q8. You have set up FlexConnect APs. For which scenario is Fast Roaming supported, providing the WLAN is mapped to the same VLAN and the client is roaming to an AP on the same Cisco WLC?
A. central switching with PMK (OKC) between different FlexConnect groups
B. local switching with Cisco Centralized Key Management within the same FlexConnect group
C. central switching with Cisco Centralized Key Management between different FlexConnect groups
D. local switching with PMKID within the same FlexConnect group
Answer: B
Q9. CORRECT TEXT
Scenario
One of your colleagues has setup a test network in the lab to simulate a new building atone of your regional offices. Your team is testing AP failover. Your colleague has requested you to configure the WLCs so that in the event of a loss of one of the WLCsthe other wings APs will fail over to the remaining WLC.
The APs on the East-WLC-2504A should fail over to the West-WLC2-2504A, and the APs on the West-WLC2-2504A should fail over to the East-WLC-2504A.
Set the priority of the APs so the backup controller recognizes the join request from the higher-priority AP and if necessary disassociates a lower-priority AP to provide access to an available port.
Not all menus, tabs and features are supported.
Topology
Answer:
Q10. Scenario
There is a problem with the East-WLC-2504A. When configuration changes are made to the Employees-East-Wing AP Group that covers the East-Wing, none of the APs receive the updates. Referto the exhibits to determine where the problems are.
What needs to be changed in the configuration of the East-WLC-2504A controller to restore functionality to the Employees-East-Wing AP Group? (Choose four.)
A. Change the AP in the Employees-East-Wing AP Group.
B. Change the IP Address in the east-wing interface.
C. Change the VLAN Identifier in the east-wing interface.
D. Enable Dynamic AP Management in the east-wing interface.
E. Change the Port Number to 2 in the east-wing interface.
F. Add the Primary Controller and IP address to the 3700-East-Wing AP.
G. Change the SSID in the Employees-East-Wing AP Group.
H. Change the Interface/Interface Group In the Employees-East-Wing AP Group.
Answer: D,F,G,H