640-692 Exam - Supporting Cisco routing and Switching Network Devices

NEW QUESTION 1
Which command displays the configuration register setting?

• A. show config-register
• B. show flash
• C. show running-config
• D. show version

Answer: D

NEW QUESTION 2
Which two of the following statements are true? (Choose two)

• A. OEM products that are built for Cisco never get a Cisco logo applied.
• B. The Cisco logo, old or new, can be found on the front bezel of all Cisco rack-mountable or desktop products.
• C. Serial numbers are attached by label on all Cisco field-replaceable parts.
• D. At the network module level, the model number is the same as the part number.

Answer: BD

NEW QUESTION 3
Which two commands are used to set the configuration register value? (Choose two)

• A. Router(config)#config-register 0x2102
• B. Router(config)#confreg 0x2102
• C. rommon>config-register 0x2102
• D. rommon>confreg 0x2102
• E. Router(config)#configuration-register 0x2102

Answer: AD

NEW QUESTION 4
Refer to the exhibit.

Into which port do you insert the card?

• A. ATM
• B. Gigabit Ethernet
• C. Serial
• D. Ethernet

Answer: B

NEW QUESTION 5
Which two statements about fiber cable are true? (Choose two)

• A. Single-mode fiber supports SC and LC connectors only.
• B. Multimode cable supports speeds between 100 Mbps and 9.92 Gbps.
• C. Single-mode cable is most appropriate for installations longer than 10 km.
• D. Fiber cable is relatively inexpensive and supports a higher data rate than coaxial cable.
• E. Mulitimode cable supports speeds between 100 Mbps and 100 Gpbs.

Answer: DE

NEW QUESTION 6
Which layer of the IOS model defines how data is formatted for transmission and how access to the physical media is controlled?

• A. Physical
• B. Data link
• C. Network
• D. Transport

Answer: B

NEW QUESTION 7
Which port displays the bootup process on a Cisco device?

• A. ATM
• B. BVI
• C. Console
• D. Ethernet

Answer: C

NEW QUESTION 8
Which two pieces of information does the show ip interface brief command display? (Choose two)

• A. Encapsulation type
• B. Interface status
• C. Layer 2 address
• D. Layer 3 address
• E. Keep alive

Answer: BD

NEW QUESTION 9
Refer to the exhibit.

Which user-mode password has just been set?

• A. Telnet
• B. Auxiliary
• C. SSH
• D. Console

Answer: A

NEW QUESTION 10
Which router can be used for disk-in-access to the router CLI management purposes and does not usually pass normal network traffic?

• A. AUX
• B. Gigabit Ethernet
• C. Fast Ethernet
• D. Channelized serial

Answer: A

NEW QUESTION 11
Which two of the following are features of NVRAM on a Cisco device? (Choose two)

• A. Stores startup configuration
• B. Stores running configuration
• C. Stores routing tables
• D. Stores decompressed IOS software image
• E. Erased when device is rebooted
• F. Not erased when device is rebooted

Answer: AF

NEW QUESTION 12
Which command is necessary to permit SSH or Telnet access to a cisco switch that is otherwise configured for these vty line protocols?

• A. transport type all
• B. transport output all
• C. transport preferred all
• D. transport input all

Answer: D

NEW QUESTION 13
Which Ethernet interface command is present when you boot a new Cisco router for the first time?

• A. speed 100
• B. shutdown
• C. ip address 192.168.1.1 255.255.255.0
• D. duplex half

Answer: B

NEW QUESTION 14
Which of the following is a DTE device?

• A. router
• B. CSU/DSU
• C. cable modem
• D. DSL modem

Answer: A

NEW QUESTION 15
Which type of memory is necessary for a router to boot?

• A. DRAM
• B. PVDM
• C. NVRAM
• D. VRAM

Answer: A

NEW QUESTION 16
Which command indicates the amount of memory (NVRAM, RAM, and flash) in a Cisco device?

• A. show diag
• B. show environment
• C. show inventory
• D. show version

Answer: D

NEW QUESTION 17
Which command can be used to identify the serial number of a Cisco router?

• A. Show run
• B. Show version
• C. Show archive
• D. Show environment

Answer: B