Q1. Which two modes of setup are offered on the initial setup script on a Cisco UCS Fabric Interconnect? (Choose two.)
A. Restore
B. Setup
C. Console
D. Serial
E. Management 0
Answer: A,B
Q2. Which type of interface is created on the Cisco Nexus 5548 Switch to represent ports connected to a FEX?
A. HIF (host interface)
B. LIF (logical interface)
C. connected Ethernet
D. SIF (satellite interface)
E. VIF (virtual interface)
Answer: E
Q3. Which two describe functions of the data center aggregation layer? (Choose two.)
A. repeater
B. high-speed packet switching
C. access control
D. services layer
E. QoS marking
Answer: C,D
Q4. Which three are the three primary methods to configure Cisco UCS B-Series systems? (Choose three.)
A. SNMP
B. XML API
C. UCS Manager GUI
D. IPMI
E. UCS Manager CLI
F. CIM-XML
Answer: B,C,E
Q5. Which item best describes the STP requirements for Cisco FabricPath?
A. RPVST must be configured on every Cisco FabricPath VLAN.
B. RPVST must be configured on every Cisco FabricPath Border interface.
C. MST must be configured on every Cisco FabricPath VLAN.
D. MST must be configured on every Cisco FPBI.
E. STP is required only to resolve border link failures.
F. STP is not required on Cisco FabricPath interfaces.
Answer: F
Q6. Which two Cisco data center devices can participate in FabricPath? (Choose two.)
A. Cisco Nexus 5500 Series Switches
B. Cisco Nexus 1000V
C. Cisco Nexus 7000 Series Switches
D. Cisco Nexus 4900 Series Switches
E. Cisco MDS 9500 Series directors
Answer: A,C
Q7. {exhibit 1805}
Refer to the exhibit. NP uplink ports connected to the core NPIV switch do not come online and are stuck in an initializing state. What is the cause that NP Uplink ports on NPV edge switch are stuck in initializing state?
A. The upstream NP Ports and the downstream server F Ports on the NPV edge switch may not be in the same VSA.
B. The core switch has not been enabled for NPIV.
C. The upstream VSAN ports and the server ports are in full duplex mode.
D. Related VSAN identifier is not allowed on Virtual Port Channels toward the edge switch.
Answer: B
Q8. Which commands issued on the Cisco Nexus 1000V VSM push the port profile named VMdata to the VMware vCenter server?
A. N1000v-VSM(config)# port-profile VMdata N1000v-VSM(config-port-prof)# no shutdown
B. N1000v-VSM(config)# port-profile VMdata N1000v-VSM(config-port-prof)# push profile
C. N1000v-VSM(config)# port-profile VMdata N1000v-VSM(config-port-prof)# state enabled
D. N1000v-VSM(config)# port-profile VMdata N1000v-VSM(config-port-prof)# update profile
Answer: C
Q9. An administrator has installed two Cisco VIC adapters. The administrator has also configured four virtual network interface cards and two virtual host bus adapters. Using this configuration, how many PCI bus addresses will be presented to the server operating system?
A. 2
B. 4
C. 6
D. 8 Answer: C
Answer:
Q10. A network engineer wants to enable a FCoE feature on a Cisco Nexus 5500 Series Switch. When does that occur?
A. after the configuration is saved and rebooted
B. after the configuration is saved
C. after at least one port is configured to operate in FCoE mode
D. after the license is applied
Answer: A