Q1. - (Topic 4)
Which command will change the database object for the primary dump device to dumplv permanently?
A. sysdumpdev –P –p /dev/dumplv
B. sysdumpdev –d /dev/dumplv
C. mkdumpdev –p /dev/dumplv
D. sysdumstart –p /dev/dumplv
Answer: A
Q2. - (Topic 4)
What are the three basic elements of RBAC in AIX?
A. Groups, Keys and Access
B. Keys, Privileges and Groups
C. Users, Groups and KeyStore
D. Roles, Privileges and Authorizations
Answer: D
Q3. - (Topic 1)
A mirrored rootvg internal disk, hdisk1, has failed and must be replaced. The remaining mirrored disk, hdisk0,is intact and functioning normally. What is the correct sequence of actions?
A. unmirrorvg rootvg hdisk1 reducevg roolvg hdisk1 rmdev -I hdisk1 -d physically replace hdisk1 cfgmgr extendvg rootvg hdisk1 mirroivg rootvg Run a bosboot on both disks
B. rmdev-l hdisk1 -d physically replace hdisk1 cfgmgr unmirrorvg rootvg hdisk1 reducevg rootvg hdisk1 extendvg rootvg hdisk1 mirrorvg rootvg Run a bosboot on both disks
C. unmirrorvg rootvg hdisk1 rmdev-I hdisk1 -d physically replace hdisk1 reducevg rootvg hdisk1 cfgmgr extendvg rootvg hdisk1 mirrorvg rootvg Run a bosboot on both disks
D. unmirroivg rootvg hdisk1 reducevg rootvg hdisk1 rmdev -I hdisk1 -d physically replace hdisk1 cfgmgr extendvg rootvg hdisk1 Run a bosboot on both disks mirrorvg rootvg
Answer: A
Q4. - (Topic 3)
Given the this output of the Iparstat -i' command from an LPAR, which statement is true?
A. There are 8 physical CPUs installed configured into 2 processor pools.
B. All active CPUs are dedicated to this LPAR.
C. There are 8 active CPUs available for sharing and another 8 active for dedicated use
D. The LPAR can automatically use up to 8 physical CPUs.
E. The LPAR can utilize processing capacity from any of the active CPUs.
Answer: E
Q5. - (Topic 2)
Anadministrator was told to reverse the search order of a working DNS lookup. During application testing it was discovered that network resolution was not working for the end users.
Given the following output, what is the most likely cause?
A. The firstDNS server is unreachable.
B. The netsvc.conf has the incorrect host lookup order.
C. Incorrect file permissions on the/etc/resolv.conf file.
D. The host is not on the network.
Answer: C
Q6. - (Topic 1)
The cfgmgr command appears to be taking an excessive time to complete. The administrator was able toquit the command and return to the command prompt. The administrator does not have access to the managing HMC and unable to check for any LED codes.
How else can the cause of the observed delay be determined?
A. Review the latest entry within /var/log/cfgdb.out.
B. Start the syslog daemon before re-issuing the command.
C. Re-issue the command with the W flag.
D. Initiate the ledmon command from a separate session, then re-issue cfgmgr.
Answer: C
Q7. - (Topic 4)
Which of the following is a requirement for EtherChannel using HEA ports?
A. Dedicated HEA portsare supported as primary adapters when they are configured at different speeds within a single EtherChannel.
B. HEA logical ports can only be used as a backup adapter when the physical ports are configured as primary adapters in an EtherChannel.
C. When using HEA logical ports as primary adapters in an EtherChannel, the underlying physical ports must be in an EtherChannel at the switch level.
D. The 'Internet Address to Ping' attribute must be enabled for logical HEA ports when the EtherChannel only includes primary adapters running at full duplex.
Answer: C
Q8. - (Topic 4)
A customer has been creating LPARs on a new POWER8 system.
After successfully activating the first 10 LPARs, the customer notices that the available RAM on physical machine reported by the HMC has reduced more than the sum of the memory currently allocated to the activated LPARs.
The Customer appreciates there will be a memory overhead for each activated LPAR, but the overhead appears more than expected.
Which LPAR attribute is the likely cause for the excess in memory consumption?
A. Active memory expansion factor
B. Maximum Virtual Adapters
C. Maximum memory
D. Maximum pages
Answer: A
Q9. - (Topic 4)
When defining a new NIM client, an administrator is prompted to select the type of network.
Why does a NIM Master prompt for this confirmation?
A. The nimesis service is not active on the client.
B. A NIM network for the hosting subnet has not yet been defined.
C. There is not Network Install Routingobject to list the route to the adjacent subnet.
D. The NIM Master’s Primary Interface has not been initialized.
Answer: B
Q10. - (Topic 4)
A failed integrated tape drive was physically replaced in a small P0WER7+ server. The
administrator attempts to use the device and receives this error message:
AN ERROR OCCURRED WHILE WRITING TO THE STORAGE MEDIA THE DEVICE IS NOT READY FOR OPERATION
Which of the following is the most likely cause?
A. The tape device microcode needs to be updated.
B. The media inside the failed tape drive was not removed.
C. The tape drive needs to be powered on before being used.
D. The drive was replaced but the new device information was not configured
Answer: D