JN0-102 Exam - Junos, Associate (JNCIA-Junos)

Question No: 2

Which class-of-service component allows you to define the bandwidth allocated to different traffic types?

A. classification

B. rewrite marking

C. scheduling

D. queuing

View Answer

Question No: 3

You have been asked to create a static route with a next hop that is not directly connected to the router.

Which configuration parameter enables the static route to accomplish this scenario?

A. resolve

B. indirect

C. next-hop

D. recursive

View Answer

Question No: 4

Which statement is correct about the validate option when upgrading JUNOS software?

A. It will check the MD5 checksum of the install package.

B. It will check if the device meets the memory requirements for the install package.

C. It will check the compatibility of the configuration with the install package.

D. It will check if the device meets the storage requirement for the install package.

View Answer

Question No: 5

Which two commands is used to validate the syntax of a configuration without applying the configuration?

A. commit confirmed

B. commit synchronize

C. commit check

D. commit and-quit

View Answer

Question No: 6

Which three steps are part of the root password recovery process? (Choose three.)

A. Reboot the device.

B. Run the recovery script.

C. Reset the root password.

D. Reset the user passwords.

E. Load factory-default configuration.

View Answer

Question No: 7

You need to control SSH, HTTP, and Telnet access to an MX240 router through any interface. You have decided to use a firewall filter.

How should you apply the firewall filter?

A. as an outbound filter on interface fxp0

B. as an outbound filter on interface lo0

C. as an inbound filter on interface fxp0

D. as an inbound filter on interface lo0

View Answer

Question No: 8

-- Exhibit -- [editsnmp] user@router# show

communityCommunityA { authorization read-only; clients {

192.168.1.0/28;

}

}

trap-groupgroupA { categories {

link;

}

targets { 192.168.100.1;

192.168.200.1;

}

}

-- Exhibit --

Referring to the exhibit, what is the purpose of the targets section of the configuration?

A. It defines which devices will be sending traps.

B. It specifies where to send traps.

C. It defines the IP addresses of management systems that can access the device.

D. It specifies which devices can be polled for SNMP data.

View Answer

Question No: 9

-- Exhibit --

user@router> show route protocol static

inet.0: 12 destinations, 12 routes (12 active, 0 holddown, 0 hidden)

+ = Active Route, - = Last Active, * = Both

192.168.1.0/24 *[Static/5] 00:03:13

>to 10.20.106.10 via fe-0/0/5.1 192.168.1.192/26 *[Static/5] 00:03:13

>to 10.20.14.131 via ge-0/0/0.0 192.168.1.192/27 *[Static/5] 00:03:13

>to 10.18.1.1 via ge-0/0/1.0 192.168.1.4/30 *[Static/5] 00:01:06

>to 10.20.14.130 via ge-0/0/0.0

-- Exhibit --

Using the routing table shown in the exhibit, what will be the next-hop IP address used for a destination IP address of 192.168.1.1? (Assume that the only routes to this destination are static routes.)

A. 10.20.14.130

B. 10.18.1.1

C. 10.20.14.131

D. 10.20.106.10

View Answer

Question No: 10

You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command. Which statement is correct?

A. The bypass-routing parameter is used to test the density on the T1 line.

B. The bypass-routing parameter cannot be used on a T1 interface.

C. The bypass-routing parameter allows you to ping a host through an interface that has no route through it.

D. The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic.

View Answer

Question No: 11

There are three static routes in the routing table that need to be announced to your OSPF peers.

Which method is used to accomplish this?

A. Apply an import policy to OSPF that injects the static routes into OSPF.

B. Apply an import policy to the static routes that injects the static routes into OSPF.

C. Apply an export policy to the static routes that injects the static routes into OSPF.

D. Apply an export policy to OSPF that injects the static routes into OSPF.

View Answer