Q1. Examine the output of the 'get router info ospf interface' command shown in the exhibit; then answer the question below.
Which statements are true regarding the above output? (Choose two.)
A. Theport4 interface is connected to the OSPF backbone area.
B. The local FortiGate has been elected as the OSPF backup designated router
C. There are at least 5 OSPF routers connected to the port4 network.
D. Two OSPF routers are down in the port4 network.
Answer: A,D
Q2. An LDAP user cannot authenticate against a FortiGate device. Examine the real time debug output shown in the exhibit when the user attempted the authentication; then answer thequestion below.
Based on the output in the exhibit, what can cause this authentication problem?
A. User student is not found in the LDAP server.
B. User student is using a wrong password.
C. The FortiGate has been configured with the wrongpassword for the LDAP administrator.
D. The FortiGate has been configured with the wrong authentication schema.
Answer: A
Q3. Examine the IPsec configuration shown in the exhibit; then answer the question below.
An administrator wants to monitor the VPN byenable the IKE real time debug using these commands:
diagnose vpn ike log-filter src-addr4 10.0.10.1 diagnose debug application ike -1 diagnose debug enable
The VPN is currently up, there is no traffic crossing the tunnel and DPD packets are being interchanged between both Ipsec gateways. However, the IKE rea time debug does NOT show any output. Why isn't there any output?
A. The IKE real time debug shows the phases 1 and 2 negotiations only. It does not show any more output once the tunnel is up.
B. The log-filter setting is set incorrectly. The VPN's traffic does not match this filter.
C. The IKF real time debug shows the phase 1 negotiation only. For information after that, the administrator must use the IPsec real time debug instead: diagnosedebug application ipsec -1
D. The IKE real time debug shows error messages only. If it does not provide any output, it indicates that the tunnel is operating normally.
Answer: A
Q4. An LDAP user cannot authenticate against a FortiGate device. Examine the real time debug output shown in the exhibit when the user attempted the authentication; then answer thequestion below.
Based on the output in the exhibit, what can cause this authentication problem?
A. User student is not found in the LDAP server.
B. User student is using a wrong password.
C. The FortiGate has been configured with the wrongpassword for the LDAP administrator.
D. The FortiGate has been configured with the wrong authentication schema.
Answer: A
Q5. Examine the IPsec configuration shown in the exhibit; then answer the question below.
An administrator wants to monitor the VPN byenable the IKE real time debug using these commands:
diagnose vpn ike log-filter src-addr4 10.0.10.1 diagnose debug application ike -1 diagnose debug enable
The VPN is currently up, there is no traffic crossing the tunnel and DPD packets are being interchanged between both Ipsec gateways. However, the IKE rea time debug does NOT show any output. Why isn't there any output?
A. The IKE real time debug shows the phases 1 and 2 negotiations only. It does not show any more output once the tunnel is up.
B. The log-filter setting is set incorrectly. The VPN's traffic does not match this filter.
C. The IKF real time debug shows the phase 1 negotiation only. For information after that, the administrator must use the IPsec real time debug instead: diagnosedebug application ipsec -1
D. The IKE real time debug shows error messages only. If it does not provide any output, it indicates that the tunnel is operating normally.
Answer: A
Q6. When does a RADIUS server send anAccess-Challengepacket?
A. The server does not have the user credentials yet.
B. The server requires more information from the user,such as the token code for two-factor authentication.
C. The user credentials are wrong.
D. The user account is not found in the server.
Answer: B
Q7. An administrator added the following Ipsec VPN to a FortiGate configuration:
configvpn ipsec phasel -interface
edit "RemoteSite"
set type dynamic
set interface "portl"
set mode main
set psksecret ENC LCVkCiK2E2PhVUzZe
next
end
config vpn ipsec phase2-interface
edit "RemoteSite"
set phasel name "RemoteSite"
set proposal 3des-sha256
next
end
However, the phase 1 negotiation is failing. The administrator executed the IKF real time debug while attempting the Ipsec connection. The output is shown in the exhibit.
What is causing the IPsec problem in the phase 1 ?
A. The incoming IPsec connection is matching the wrong VPN configuration
B. The phrase-1 mode must be changed to aggressive
C. The pre-shared key is wrong
D. NAT-T settings do not match
Answer: C
Q8. Examine the following partial output from two system debug commands; then answer the question below.
Which of the following statements are true regarding the aboveoutputs? (Choose two.)
A. The unit is running a 32-bit FortiOS
B. The unit is in kernel conserve mode
C. The Cached value is always the Active value plus the Inactive value
D. Kernel indirectly accesses the low memory (LowTotal) through memory paging
Answer: A,C
Q9. Examine the output of the 'diagnose sys session list expectation' command shown in the exhibit; then answer the question below.
Which statement is true regarding the session in the exhibit?
A. it was created by the FortiGate kernel to allow push updates from FortiGuard.
B. it is for management traffic terminating at the FortiGate.
C. it is for traffic originated from the FortiGate.
D. it was created by a session helper or ALG.
Answer: A
Q10. Examine the following partial output from two system debug commands; then answer the question below.
Which of the following statements are true regarding the aboveoutputs? (Choose two.)
A. The unit is running a 32-bit FortiOS
B. The unit is in kernel conserve mode
C. The Cached value is always the Active value plus the Inactive value
D. Kernel indirectly accesses the low memory (LowTotal) through memory paging
Answer: A,C